0
How do you remove the shaft between spider gears in a rear axle?
Wiki User
∙ 12y ago
Remove the bolt in the pin then u may have to get a chisle and hammer and knock it out
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you remove rear axle 2003 gmc Yukon?
Remove wheel, Remove drum or disc brake rotor,remove rear differental cover. Remove shaft between the spider gears that is held in by a lock bolt. Shove the axle from the outside toward the differential and remove the "C" clips that hold the axle in inside the diff. and then the axle can be removed.
How do you take the axle out of a Chrysler 8.25?
To remove the axle shaft, first remove the wheel, and brake drum/rotor. Second, remove the differental cover. Third, remove the bolt holding the spider gear shaft, and remove that shaft. Fourth push inward on the axle shaft to remove the horseshoe clip on the inside. The axle shaft will now pull out.
What are camshaft gears?
Camshaft gears are the gears that drive shaft that operates the cams.
Is there a tool for the removal of the c clip that retains the axle in the rear end of a 96 S-10 Chevy Blazer 4x4?
it should come out easily. push the offending axle inward so you can see the retaining clip and remove it. then pull the axle out of the housing. repeat on other side. you have to remove the "spider" shaft first or the axles cannot be pushed inward (it is in the way) Often, the spider shaft is held in with a little screw that has an elongated point or shaft. remove it completely and the spider shaft should slide out. the do the axles.
How do you pull axle out of Chevrolet limited slip diff?
Why would youwant a vehicle manufactured by a corporation that, due to their shoddy designs, ultimately found themselves in Bankruptcy?Dump it. wow! informative answer Einstein, next time you post an answer make sure it is correct, you really missed the boat on this one! Remove diff cover and look for small bolt with 5/16" or 7mm head holding cross shaft in gear carrier. Remove bolt, then remove cross shaft, be very careful not to spin spider gears out of carrier when cross shaft is out. Also be careful to look for and not lose shims between spider gears and gear carrier. Push axle that you want to remove all the way in and look at inner end of axle (inside of gear carrier) you will see a c-clip. Spin c-clip off with small screwdriver (pocket screwdriver size) and pull axle out. Install in reverse order.
What are camshafts?
Camshaft gears are the gears that drive shaft that operates the cams.
How do you replace the rear wheel seal on a 1992 Chevy blazer?
You have to open the differential and remove the retaining pin from the spider gear to remove the axle shaft.
Where is the differential located on a Ford F-150?
The differential (rearend) is what your back wheels and drive shaft are bolted to. If you have a 4 wheel drive there is one at the front as well. The differential has a series of gears ( spider gears ) inside. This allows for the difference of the speed between the left and right wheels when turning corners or going over bumps ect.
How do you remove rear axle from 1999 Olds Bravada 3rd member in order to change bearing?
Remove 10 bolts holding rear cover. Rotate ring gear till you find 3/8 hex bolt on side of ring gear carrier. Removal of this bolt will allow you to remove spider gear cross shaft. [Spyder gears are 4 small gears in ring gear carrier,DO NOT REMOVE SPYDER GEARS!] Now push in axle that you want to replace and remove large c-clip that holds axle in. When reassembling you must use Loc-Tite on 3/8 hex bolt.
What is the funchion of a spider gear pin in a differential?
It keeps the spider gears spread apart , to mesh to the Differential output shaft gears ( 2) , one on each side of of the spider gear set , inside the Differential Housing . What I was trying to find was a Modification to a Traxxas Rustler / Nitro Sport Diff , that you took a longer pin and cut it just a small bit longer , which in turn , is suppose to force the spider gear teeth ( further ) into the Diff output shaft , gear teeth , for better tooth contact area , hence .... less gear tooth breakage .....maybe last longer also.
What is reverse shaft?
A Reverse Shaft is the shaft which rotates in the opposite direction of the engine driver shaft with the help of meshing of gears mounted on it to the gears mounted on engine driver shaft when reverse gear is applied. The reverse shaft allows the vehicle to move in reverse direction. Sanjay Singh Rathore (ME 3rd year) M.I.T.Mandsaur
What is the function of the propeller shaft?
The function of anything with the word "propeller" on any vehicle is the object that "propels" the vehicle, or makes it move. A propeller shaft on a car links between your differential and you transfer case or transmission. The engine essentially rotates the gears in your transmission which in turn rotates the prop shaft itself, or the gears in the transfer case, which also rotates the propeller shaft. The shaft then turns the gears in the differential. The gears in the differential then turn you axles, which in turn rotate your wheels, propelling the vehicle. As for an airplane, a propeller forces air in the direction of the rear of the plane thrusting (propelling) the plane forward. Same idea with a boat only it forces water back causing the boat to be propelled forward.
