0
How do you remove the slide and barrel from a smith and Wesson model 422?
Wiki User
∙ 15y ago
You can request a owner's manual at the S&W web site.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Disassembly for Smith Wesson Model 39?
SLIDE THE SLIDE BACK TILL THE SLIDE RELEASE IS IN THE NOTCH IN THE SIDE PUSH RELEASE THROUGH THE FRAME AND SLIDE THE SLIDE FORWARD OFF THE FRAME THEN TURN THE BARREL NUT AND REMOVE THE RECOIL SPRING AND GUIDE THEN THE BARREL WILL SLIDE OUT OF THE SLIDE
How do you remove the bolt from a Stevens model 62 22 Lr?
You have to remove the barrel. Take the stock off and you will see the nut that holds a "U" clip in place. The clipp holds the barrell. Remove clip, slide barrel out, then the bolt will also slide out.
Disassembley for smith and Wesson 909?
Make sure the weapon is unloaded, remove the magazine and then make sure the safety is in the off position. Pull the slide to the rear about 1 inch until the slide stop is below the notch in the slide. Hold the slide in that position and push the slide stop pin from right to left and remove the pin. Let the slide move forward and off the frame. At this point, you have access to the recoil spring and barrel. You can remove the recoil spring, guide rod and barrel at this point.
How do you remove ignition barrel on vt?
The ignition barrel can be removed by removing the retaining ring. The barrel will slide out. Remove the wiring harness from the back of the barrel.
How do you disassemble a Smith and Wesson Model 59?
Pull the slide back until the notch on the slide closest to the muzzle is over top of the slide-lock pin. While holding the slide back, push the slide-lock pin out (push from the right hand side of the gun). Slowly allow the slide to go forward. Release the hammer gently. Pull the slide towards the muzzle and it should slide right off. Remove the guide rod and recoil spring from the underside of the slide. Then twist the barrel bushing at the muzzle and pull it out so that the barrel can move. Pull the barrel out from the underside of the slide. This is the least amount of disassembly needed for a proper cleaning. You will want to clean the barrel, inside and out, as well as the underside of the slide, and any other parts inside that may have dirt, oil, residue or other fowling. Re-oil the weapon and assemble using the steps above in reverse.
How do you remove the slide lock pin on the Smith and Wesson Model 59 Pistol?
Ask a gunsmith for help or contact S&W for an owner's manual. You can also download one from their website.
How do you disassemble a smith Wesson model 459 pistol?
Remove the magazine and clear the chamber. Make sure the gun is NOT loaded. Set the safety in the up "fire" position. Pull the slide back just enough so the slide catch notch in the bottom left side of the slide is even with the front of the slide catch. If you pull the slide back far enough to engage the slide catch you have gone too far. When the notch in the slide is over the pin of the slide catch push on the pin from the right side of the frame. The button like end of the pin is just above the trigger on the right side of the frame. Push in this "button" you may need something like a pen if you cant push it with you finger. Fully remove the pin from the frame. Pull the slide forward out of the frame. Carefully remove the recoil spring and guide. Rotate the barrel bushing to the left and remove from the slide. Pull the barrel up and out of the slide. This is the standard field strip for this gun. Refer to a gun smith for further disassembling.
How do you clean a sw 39?
make sre it's unloaded,push slide back till notch in slide lines up with slide lock-push it through to the other siide&out pull slide off frame,remove spring&rod from unger barrel & remove barrel
How do you remove a Remington 1100 barrel?
First pull back the slide until it locks in a open position then remove the end off of the forearm and then remove the forarm then proceed to remove the barrel.
Where do you find the model number on a smith and wesson 22 long rifle revolver?
Inside the crane or on the slide
How do you remove the slide from a smith and Wesson 39-2?
Go to S&W's website and request a manual.
How do you disassemble a model 457 smith Wesson 45 caliber?
You hold the slide back about half way and push out the slide retaining pin. At that point, the slide will come off the frame.
