answersLogoWhite

0


Best Answer

It has no governor. Speed is controlled by the computer.

User Avatar

Wiki User

โˆ™ 2010-11-07 15:56:51
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you remove the speed governor on a 95 Chevy s10?
Write your answer...
Submit
Related questions

How do you take off a governor on a 1999 Chevy s10?

It has no governor. Speed is controlled by the ECU.


How hard is it to remove a 1992 Chevy s10 5 speed transmission?

If you have the right tools and a transmission jack, it's quite easy.


How hard is to remove a 1992 Chevy s10 5 speed transmission?

If you have the right tools and a transmission jack, it's quite easy.


What type fluid goes in 5 speed s10 Chevy pu?

I used Mercon in my 98 S10 2.2 standard 5 speed transmission.


How do you remove bench seat in 1996 Chevy S10?

Remove the bolts from each corner.


What is the difference between an S10 and a Chevy S10?

An S10 is the same as a Chevy S10.


Speedometer cable transmission on a Chevy s10?

It uses a speed sonsor on the trannie


How do you remove the clutch cable on a 1996 Chevy s10?

There is no cable, it is hydraulic operated.


How do you remove a driver seat to a 1991 Chevy s10?

Unbolt it from inside, lift it out.


Does the vehicle speed sensor control the idle in a Chevy blazer s10 1989 2.8?

No it does not.


How to Remove governor in 1998 s10?

under your truck their is a sensor that is mounted to the transmission that is a two pronged plug just remove it and you are done... your s10 should push 130-140 plus


What years will a 1998 s10 transmission interchange?

I've got a 2000 chevy s10 2wd 5 speed I'm putting a 305 v8 in it will the 5 speed work on it


How do you remove a you-joint on a 1996 Chevy s10 blazer?

or you talking about the driveshaft u-joint?


Do you have to remove the dash to replace the heater core in a 1994 Chevy S10 pickup?

Yes.


Why would 4wd on 2001 Chevy S10 Blazer not work properly after changing accuator and speed sensor?

A 4WD on a 2001 Chevy S10 Blazer does not work properly after changing its actuator and speed sensor probably due to shorted wires. Also check for loose wiring.Ê


How do you change oil sensor on 1996 Chevy s10?

If that S10 has a 4.3 engine, I find it best to remove the distributor to gain better access to the oil pressure sensor.


What fluid type is used in a 1998 Chevy s10 speed manual transmission?

Mercon works.


What is the average mpg for a 4-cylinder 5-speed 1998 Chevy S10?

99 mpg


How do you adjust idle speed on 1993 Chevy S10 pickup with a 2.8 liter?

May be computer controlled and not adjustable


Where is the speed censor located in a Chevy s10 4wheel drive truck?

In the back end of the transmission.


Will speed sensor on Chevy S10 blazer cause it not to shift into high gear?

Yes, it could.


How do you remove axle on 91 Chevy s10 2wd?

you have to remove the diff cover then there shud be to c clips u remove thows and they shud just pull right out


Whereis fuelpumplocated on chevys10blazer?

where is the fuel pump located and how to remove it on 1994 Chevy S10 blazer


Allen wrench size needed to remove caliper on a s10 Chevy blazer?

3/8"


How do you remove tailgate cables on a 2003 Chevy S10?

The latch assembly and cable is one piece.