answersLogoWhite
Pontiac Grand Am
Pontiac Sunfire
Door Panels and Handles

How do you remove the window handle from a 1998 Pontiac Sunfire?

111213

Top Answer
User Avatar
Wiki User
2008-03-10 19:08:32
2008-03-10 19:08:32

Don't know, would like to know.

1

Related Questions

User Avatar

You can get a Window handle remover from an automotive parts store that'll help remove a clip that holds on the handle. With this you can remove the clip and then the handle.

User Avatar

There is u- shaped flat peice of meltal and it's a window handle clip remover Auyo zone has thewm and they do now cost much! Good Luck!

User Avatar

How do you remove the manual window cranThere should be an Allen type set-screw in the base of the handle. It will be recessed, and you'll have to turn the crank to access it more easily. Remove the setscrew, and the handle slips off of the stud. If the window is down, and it begins to rain, you can roll the window up by holding it onto the stud, and turning, or you can use a small pair of vise grips. Just try not to damage the teeth on the stud.

User Avatar

there is a clip on the back side of handle u will need a special tool for that just go to a local automotive shop im sure they will pop it off for u and u can just put the clip back on the handle and push it on ur self when ur done

User Avatar

how do you remove a car handle window for a 1995 lincoln car?

User Avatar

It requires a special tool available at the parts store cheap. Use 2 Screwdrivers, force a rag between the door and the window crank handle to give you some space, then pry the clip apart or take a small hook, hook under the loop of the pin and pull up.

User Avatar

Remove inside door handle and window crank handle, remove inside door panel, remove vent window and channel assembly, remove window.

User Avatar

There is a "C" clip behind the handle that has to be removed. Your local auto parts store can sell you a simple tool to remove that clip for less than $10.

User Avatar

You have to pry the clip out of the slot behind the handle

User Avatar

To replace the window crank handle on the 1993 Geo Prism, first remove the interior door panel. Then, access the screw that holds the window crank in place and remove it. You can then remove the handle itself.

User Avatar

remove the door panel and the window crank (if manual windows) , if auto windows remove the piece behind the door handle and unclip it from the buttons unscrew all screws around the door panel with a regular screw driver once you have done all that u will see the speaker remove it with a star head screw driver

User Avatar

check the fuseor the plugin at the rear window or mabey a broken wire

User Avatar

look up under the back window through the trunk and you will see them right there.

User Avatar

Trust me there is a clip it is a real cheap wire horseshoe shaped clip, the only way to remove this clip is you need to purchase a tool just for removing clips on window cranks.

User Avatar

You will need to remove the inside door panel. Remove the door handle retaining screws. Remove the linkage from the back of the door handle.

User Avatar

Assuming its not a power window...and you wnat to remove the cranking handle... Possibility: look behind the handle for a U-shaped spring clip that fits into slots on the handle "sleeve". This clip will have two small tangs that can be levered to push it back out of the slots in the handle.

User Avatar

If your window is like my grand am the glue that holds the track and window together is not holding properly, so window keeps coming off track. I have not found a glue that holds yet.

User Avatar

Remove the inside door panel. Remove the Allen screw from the window crank linkage. The window crank handles should come off.

User Avatar

there is a small clip between the handle and door panel that u have to remove it is easy if u have a small pick to hook it with then to install just place clip on handle and push on the window regulator shaft.

User Avatar

How to Remove or Install Car Window Crank Handles check related link below

User Avatar

You can use a bolt and lock nut, probably 1/4 inch.

User Avatar

If there is no faster head visible then it likely is attached with a clip on the backside of the crank handle. slip the handle between the handle and door panel to remove the clip.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.