i use a flat head screw driver cause i know how to manipulate the pin in how to knock it out from behind the crank but they have a special tool that makes this very simple go to any auto part store and ask them for the tool that removes this pin and when you go to remove this pin there is a plastic retainer in front of the door panel then the door crank has the U shape pin going through it use this tool by sliding it down on top in front of the door paanel and that retainer on top of ther crank it self and try turning the crank until you feel the tool drop down and then try pulling with ease out towards you and it should remove rather easily if not then pull the tool back up just enough to make another turn and repear the process till it drops down and then it should slide rite off. MOST OR ALL SATURNS ARE THE SAME WITH THIS WINDOW CRANK
With a hammer and pry bar.
Push the door panel in around the window handle and use a screwdriver or a piece of wire with a hook to pull the clip off....it's in behind the handle.
Lift up on the handle. You should see plastic inserts that fit into two tiny holes. Remove the inserts and the handle should slide to the side.
no sweat,undo the bolts around the door they are 30 torqs bit,remove the outer handle which has a small clip than you pull the handle to the side to remove than with the window open shut the door and the panel will come strait off.
How to remove the window motor from the regulator
You have to pry the clip out of the slot behind the handle
Remove the inside door panel of your 1999 Chrysler Intrepid. Remove the window retaining clips. Put the window back into the window track. Secure the window with the window retaining clips.
See link below:
To remove the handle the inside door panel has to come off,with the window up.there is a small bolt insde and one at the end of the door by the handle take those two off and the linkage inside...yes you need small hands.
How do you remove the manual window cranThere should be an Allen type set-screw in the base of the handle. It will be recessed, and you'll have to turn the crank to access it more easily. Remove the setscrew, and the handle slips off of the stud. If the window is down, and it begins to rain, you can roll the window up by holding it onto the stud, and turning, or you can use a small pair of vise grips. Just try not to damage the teeth on the stud.
Remove the inside door panel of your 1999 Mercury cougar. The entire window mechanism will be visible. Remove the wiring harness from the window motor. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install your new window motor.
Lower the rear window down. Remove the screw that is under the door handle and remove the plastics bezel. Pull window switch upwatds and disconnect wire. Remove plastic cover under door handle and remove 2 bolts that are behind the plastics piece. Gently prior the door panel off from all edges. Remove door panel. Three bolts hold the rear window channel in place. One is one the door frame , one at the top of the channel at the top edge of the window, and one is on the bottom of the window frame. Look at the new window strip to determine locations. Remove old weatherstripping and reverse above back into place.
The starter for a 1999 Saturn is on top of the transmission under the air filter box. Remove the filter box for easy access.
with a brick
You must remove the Timing chain cover and engine girdle.
You will need to remove the inside door panel of your 1999 Ford Escort. Loosen the retaining clips on the window. Remove the window from the window track. Reverse the process to install the new window.
It takes a special tool. Not expensive at the parts sttore.edit by jwko - My gosh, it takes no special tools. Roll the window up and remove inside door panel. Be careful if you have any pwr windows/locks/mirror switches. You should be able to pop those out first and remove wiring harness. When you remove the inside door panel you sould be able to see how to easily remove the door handle assembly.
You have to take off the door handle. You have to disengage the door locking mechanism from the door handle, then unscrew the panel and take it off. The door handle unhinges from the locks and from the window controls. If your windows are electric, just unsnap the cord attached and leave it hanging out. You may have to work with the door handle as it won't come out of the slot very easily and you don't have a lot of room. A flat bladed screwdriver with a long metal piece should work to unsnap it.
With a test light.
Remove the instrument cluster then replace the bulbs. = =
take it to safelite lol
Remove the inner door panel.See link below.