answersLogoWhite
Door Panels and Handles
Home Improvement
Windows 98
Windows XP

How do you remove window caulk?


Top Answer
User Avatar
Wiki User
Answered 2007-09-03 12:58:55

Heat gun, or a hair dryer set on high

heat the caulk, to soften it, peel it off,

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Related Questions


With the caulk remover tool by Black and Decker


A silicone caulk is the best. It's the easiest caulk to apply and also remove if needed.


You can use a flat-head screwdriver to remove the caulk by piercing the caulk and digging it out. There are also special made tools for removing caulk that can be bought in hardware stores. For smaller bits of caulk, you can buy a solvent that will loosen it up, allowing the caulk to be easily removed with a paper towel


freeze it then peel it off


Yes you can, but it is a cleaner job if you remove the old caulking (as much as you can) and reseal it with new caulk.


You can use 3m's caulk remover and a sharp razor blade.


To remove silicon caulk from an enamel bathtub, you should use some type of putty knife. You could also use a razor blade.


Hi You can use solvent or stripping agent to remove silicone caulk from tiles. Find more helpful tips, ideas at http://www.gharexpert.com Thanks


Not the greatest idea, when packing in the oakum and then pouring the lead and caulking it the hub could split wide open Your new caulking job will last longer if you remove the old caulk and any of its debris and make sure the area is dry before adding new caulk. You can use an old screwdriver to remove the old.


Use an exterior window caulk. If you plan to paint over it make sure it is "paintable" caulk. Run the bead of caulk using a caulking gun. You can smooth out the bead with your finger and clean up any residual caulk with a wet rag (this clean uo only works if the caulk is water based...check the tube to make sure it is....it's easier if it is) If you use silicone caulk you can't paint it and you cannot clean up any errors with a wet rag so unless you are real exact in applying the bead I would avoid this type of caulk.


u cant ive tried nothing works


Have to remove the door panel screws, then remove speaker, drop the cables off the window motor (maybe), drill out the rivets that secure the regulator at bottom and remove two bolts at the top of regulator. push window all way up remove glass from regulator, I used a screwdriver but am sure there must be an easier way to remove the caulk that hold window to regulator. then dats about it..if you need to replace motor same thing drill out the rivets and pull out from right side of door...have fun that project sucked for me..LOL


a screw driver and hammer-be careful not to scratch the tile or a chisel or putty knife and a hammer- test it out and see what works best for you- you can also just remove half of it and re caulk to make it look clean


Remove inside door handle and window crank handle, remove inside door panel, remove vent window and channel assembly, remove window.


Remove the inside door panel of your 1982 Chevy Corvette. Remove the window retaining clips. The window will lift out.


First remove the door panel.Then remove the moisture barrier.Next remove the window motor from the window regulator.


Disconnect the battery.Remove the door panelRemove the power window motorRemove the regulator spring.Move the window down a bit and remove the two 10MM nuts from the window.Twist the window spring stud counter-clockwise.Now you should be able to remove the window regulator.


To remove the drivers side window and regulator, you will need to remove the door panel from the door. Then you can unbolt the regulator and window to remove them.


Remove the inside door panel of your 2002 Chevy Cavalier. Remove the window motor wiring harness. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install the new window motor.


Remove the inside door panel of your 1994 Chevrolet Corsica. Remove the window motor wiring harness. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install the new window motor.


Remove the inside door panel from your Mercedes-Benz. Remove the wiring harness from the window motor. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install your new window motor.


Remove the decorative cover to the window switch panel. Remove the window switch retaining screws. Remove the wiring harness from the back of the window switch. Reverse the process to install the new window switch.


Remove the inside door panel. Remove the wiring harness from the window motor. Remove the track linkage. Remove the window motor retaining screws. Reverse the process to install the new window motor.


Remove the inside door panel of your 1997 Mercury Cougar. Remove the wiring harness from the window motor. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install the new window motor.


Remove the inside door panel. Remove the window motor wiring harness. Remove the window motor retaining bolts. Reverse the process to install the new window motor.



Copyright ยฉ 2021 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.