0
Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. Check the windshield wiper motor for proper operation and the wiper arms for adjustm
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you replace a wiper motor on a f150?
If you'd like to replace a wiper motor on a Ford F-150 you need disconnect the negative battery cable, remove mounting bolts, and replace old wiper with new unit. When you've installed new unit connect electrical harness and wiper arm to motor.
How do you replace a windshield wiper motor for a 1998 f-150?
To replace a windshield wiper motor for a 1998 F150, first remove the bottom trim on the window. Then remove both wiper blade assemblies and all screws on the metal cowling. Remove the retaining clip from the wiper motor linkage and pull the controls rods off.
Changed wiper motor and switch wiper still don't work on my 97 f150?
Check fuses and relays
1998 f150 wiper motor doesnt work?
check fuses or relays
Where is the windshield wiper motor on a 1993 Ford F150?
top of the fire wall under the hood your wiper arms will connect
Where is the Windsheild wiper fuse for 1999 F150 located?
Its in the fuse box under the stearing wheel.
Where is the windshield wiper motor governor found on a 1990 Ford F150?
The governor for the wipers is located near the fuse box. It is wired to the harness going to the wiper switch.
Can you replace oil pump on 1978 f150 with 351 winsor without lifting motor?
Yes, you can replace the oil pump in a 1978 F150 with 351 Winsor without lifting the motor. To replace the oil pump you will need the proper tools and supplies.
How do you replace the blower motor resistor in a 1999 Ford F150?
it is located and accessible under the dash by the front passenger floor board. need 8mm nut driver only. easy
How do you replace freeze plugs between the motor and transmission on a 1997 Ford Taurus?
how do you replace the freeze plugs between the transmision and motor on a 1997 f150 5.4
Windshield wipers not working 1998 ford f-150?
If the windshield wipers are not working in a 1998 Ford F150, the cause could be a blown fuse. There could also be a problem with the vacuum hoses connected to the wiper motor or the wiper motor itself.
How do you replace a turn signal and windshield wiper assembly on a 1998 Ford F150 4x4 4.2 LT with AC?
Take it to a Ford Dealer.
