0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Door won t shut?
sunfire drivers door latch won t work
Car door wont shut on a 1994 Ford T-bird- Only closes when the latch on side of door that holds onto metal bar on car frame is flipped up- any suggestions?
If the door will not close on a 1994 Ford Thunderbird unless the latch is flipped up, the latch is gummed up. Spray the latch with WD-40 or Liquid Wrench to free up the latch mechanism. A door that is out of alignment will also cause this type of problem. Check the hinge and inspect for cracks that might allow the door to droop.
How can you adjust the driver's side door of a 1989 Ford Thunderbird so it will close right?
CHECK THE HINGES. IF THEY ARE BENT YOU MAY NEED TO REPLACE THEM. THIS IS WHAT I HAD TO DO WITH MY T-BIRD AND THE DOOR SHUT BEAUTIFUL. GOOD LUCK!
Are a 1994 and 1995 t bird door interchangeable?
Yes!
Were can you get 1987 T-bird door seal?
Just about any auto parts store can get one for you.
The voltage regulator won't kick in to charge the battery on my 1985 t-bird?
replace the voltage regulator
What if the door lock don t work what you have to do 1994 mark viii?
replace the door lock accuators. should only be 50.00 for the part
How do you replace the fuel tank in 97 T-bird?
I have an 86 t-bird 3.8 liter and need to know how to drop the fuel tank. I need to know where to disconnect all lines and connections to the tank. thanks
How do you fix courtesy lights that refuse to go out on 2000 F350 ford including door ajar icon on dash?
do not look for door jam switch;because when you find it just replace it. the switch is located inside the door and mounted on the door latch. this switch gets very dirty you can try to clean it.if it was me CHANGE IT Ther is a little plastic push button on the bottom inside of the of the front door post.some times this will corrode or a wire will break.This is leaving the connection open and the light won,'t go out when you close the door.
How do you repair exterior door handle on 1989 Chevrolet truck?
Remove perimeter trim panel around inside door latch held in by 5 friction clips (pop out w/screw driver. Remove inside door trim panel held on by plastic T clips (just pull and lift up). Drill out 4 pop rivets holding window mechanism. remove clips holding ends of door latch linkage rod. Remove inside 12mm bolt left side of handle and then the 12mm bolt inside door jamb area. Take out 3 torx screws holding door latch assembly, and slide the latch and door handle assembly up enough so that the linkage rod clip to the back of the lock assemble can be removed. The handle assemble can noe be pulled out and replaced - takes about an hour.
What is the cost to replace intake manifold gasket on 1996 ford t-bird?
Every place charges different. Call and ask.
How do you remove the outer door handle on a ford freestyle?
Removal of Rear Door Latch is necessary first. Rear Door Latch Removal: All vehicles 1. Remove the rear door interior trim panel. 2. Remove the access hole watershield. 3. Reconnect the window regulator and window switch electrical connectors and position the front door window to access the glass clamp bolt. 4. Disconnect the window regulator and window switch electrical connectors. 5. Loosen the window glass clamp bolt. 6. Tape the window in the full up position, then lower the window regulator downward until it reaches the stops at the bottom of the regulator track. 7. Remove the interior door handle bolt. 8. Disconnect the rear door latch assembly electrical connector. 9. Rotate the push button rod downward and remove it from the rear door latch assembly. 10. Remove the 3 rear door latch assembly-to-rear door module bolts. 11. NOTE: Make sure that the interior door handle does not get scratched when it is passed through the rear door module. Remove the 8 bolts and position the rear door module aside. FIVE HUNDRED AND MONTEGO 12. Remove the tape and lower the window glass. 13. Remove the scrivet. 14. Remove the rear door glass run top bolt. 15. Remove the rear door glass run seal. 16. Carefully position the glass aside, then remove the rear door glass top run. ALL VEHICLES 17. Disconnect the exterior door handle actuating rod from the rear door latch. 18. Remove the 3 rear door latch bolts. 19. Remove the rear door latch assembly. 20. Remove the remote cable cover from the latch. 21. Disconnect the interior door handle actuating cable from the rear door latch. 22. Remove the rear door latch from the bracket. * If necessary, remove the door lock actuator and the door ajar switch. INSTALLATION ALL VEHICLES Note: If necessary, install the door ajar switch and the door lock actuator. 1. Install the rear door latch on the bracket. 2. Connect the interior door handle actuating cable to the rear door latch. 3. Install the remote cable cover on the latch. 4. Position the rear door latch assembly. 5. Install the 3 rear door latch bolts. * Tighten to 12Nm (9 lb-ft). 6. CAUTION: The exterior door handle and the door latch must be installed and tightened to specification before connecting the exterior door handle actuating rod with the yellow clip. CAUTION: The exterior door handle actuating rod must be hanging freely then clipped into the door latch. Loading the exterior door handle actuating rod up or down when connecting may result in a misadjustment of the latch causing the latch not to operate correctly. Connect the exterior door handle actuating rod to the rear door latch and close the yellow clip. FIVE HUNDRED AND MONTEGO 7. Install the rear door glass top run and carefully position the glass. 8. Install the rear door glass run seal. 9. Install the rear door glass run top bolt. 10. Install the scrivet. 11. Raise the window glass and tape it in the full up position. ALL VEHICLES 12. NOTE: Make sure that the interior door handle does not get scratched when it is passed through the rear door module. Position the rear door module and install the 8 bolts. * Tighten to 8 Nm (71 lb-in). 13. Install the 3 rear door latch assembly-to-rear door module bolts. * Tighten to 12 Nm (9lb-ft). 14. Install push button rod on the rear door latch assembly. 15. Connect the rear door latch assembly electrical connector. 16. Position the interior door handle and loosely install the bolt. 17. Untape the window glass, then lower the window glass. 18. Install the window glass clamp bolt, * Position the window in the window clamp. * Shift the door window glass fully forward. * Tighten to 8 Nm (71 lb-in). 19. Install the access hole watershield. 20. Install the rear door trim panel. 21. Center the inside door handle alignment pins to the rear door trim panel and install the interior door handle bolt. * Tighten to 7 Nm (62 lb-in). EXTERIOR REAR DOOR HANDLE REMOVAL: Remove: 1. Remove the rear door latch. 2. CAUTION: Hold the bezel cap when removing the bolt or damage to the door may occur. Using a T-5 torx socket installed on the bolt tip, loosen the bezel cap bolt until the bezel cap can be removed. 3. Shift the exterior door handle rearward and remove the exterior door handle. 4. Remove the exterior door handle gasket. 5. Loosen the exterior door handle reinforcement bolt. 6. Remove the exterior door handle reinforcement from inside the door. 7. Release the bezel cap from the bezel and remove the bezel cap bolt. INSTALLATION 1. Install the exterior door handle reinforcement on inside the door. 2. Tighten the exterior door handle reinforcement bolt. * Tighten to 7 Nm (62 lb-in). 3. Install the exterior door handle gasket. 4. Install the exterior door handle. 5. Install the bezel and the bezel cap bolt. * Tighten to 12 Nm (9 lb-ft). 6. Position the exterior door handle forward. 7. Snap the bezel cap on to the bezel. 8. Install the rear door latch.
