0
Remove the injector and you will see the o-ring.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
PO446 97 Lexus es300?
Your gas cap may have been left loose or the oring on the cap needs replaced unless you have lost it. If this is the case do yourself a favor and buy the thirty dollar Lexus replacement
How do you replace the fuel injectors on a 2000 dodge ram?
remove fuel rail above the injectors un hook the wire and pop it out clean around the injector before removeing it keep the dirt out of the cyl use alittle grease on the oring when you put the new one in
When was Nicole Oring born?
Nicole Oring was born on January 19, 1977, in Seoul, South Korea.
Why is new caliper leaking?
There are two reasons i know of . first the oring in the piston is either cut or twisted. The other is that the o ring on the piston is to small. The only cure is to replace it either way.
Groove depth for a 3.5 mm oring?
4.3 for static
What has the author Stuart A Oring written?
Stuart A. Oring has written: 'A comparative investigation of the similarities and differences in the aesthetic theories of Alfred Stieglitz, Edward Weston, Ansel Adams, and Minor White'
After installing a new fuel pump on a 1990 caprice how do you reattach that metal ring to the tank to finish the procedure?
that is a tricky metal ring (locking ring) there is a special tool for that.but if you are going to do this once no need to spend the money on a tool you will never use again. the trick is to get all the tabs started at the same time. there is an oring and you need to push the metal ring straight against the oring and turn clock wise until all the tabs catch. then get a chisel or screw driver and a hammer. there are outside tabs on the metal ring. tap them and turn the whole thing in clock wise.wala It is easier to fit the oring...if you will be sure the area is clean of any dirt and grit. Grease the area lightly on the tank, the area also where the oring contacts the tank, and the locking ring side to oring. Press firmly together, all tabs do need to be interlocked. Be sure oring is under and sealing. DO NOT STRIKE lock ring , to fit it in place. NO SPARKS.
Why paintball gun leak out barel when put on co2?
most likely a valve oring in damaged.
How do you replace fuel tank sending unit?
Disconnect the hoses and electrical connections from the sending unit, rotate the locking ring counter clockwise until the "ears" of the locking ring line up with the opening on the tank, remove the locking ring, remove the tank sending unit, inspect the oring and mating surface on the tank for debris, reinstall the oring and new tank sending unit, install locking ring and rotate clockwise until it hits the stops, then reconnect hoses and electrical connections.
On a 93 lumina 31 liter can the oil pump drive be remove without removing the oil pump the drive leaks oil at the block seal and I'm trying to remove it to replace the seal?
the head has to be removed in order to get the drive out all of the way, but the easy way is to cut a notch at the top of the drive where it hits the head to get to the oring while it is still in the block then slide the oring over the top (after soaking in hot water is easier) once you get the new oring on get a SBC dist. gasket, splice it and put it around the top of the drive, the get some RTV silicone and goop it up to seal the gasket back together, this way takes about 2-3 hours and is WAY easier than removing the head,
Why does your 1997 Buick Riviera engine has gas in the oil?
Answerbad fuel injector oring, leaking internally take to a qualified mechanic for replacement of intake manifold, gaskets, possible engine rebuildCould also be a bad fuel pressure regulator. Or could be running rich due to bad/dirty MAF sensor, temp sensor, over due tuneup, or poor ignition or bad computer.
How do you change the distributor o ring on a 1997 Mitsubishi Galant?
remove the distributor and remove the oring. reverse removal procedure...oh be careful that you put the dist back in same way it came out or it wont start.this is done by marking rotor position. You also will need a timing light to reset timing. lubricate new oring
