answersLogoWhite

0


Best Answer

Get a pair of pliers. Push the brake light assembly to the left, it will easily slide on the carpet. Once pushed over to the left all the way, notice the groove in the carpet to the left of the assembly.The groove is for your finger to pop the entire assembly off the carpet. After it's off the carpet, slide the electrical plug off the assembly. Now you can use the pliers to turn the plastic piece holding the bulb (be gentle, it's plastic). After it has been turned, it will come out, then you can remove the bulb with your finger. I took the bulb to Toyota for a genuine replacement (cost $5.00). Slide the new bulb in, reconnect the electrical cord, and pop the assembly back onto the back of the car, and remember to slide it back to the right. You just saved yourself some cash!!

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you replace high mounted stop ligh 2005 Lexus ES330?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What brand is the 6 CD changer in the 2005 Lexus ES330?

Pioneer is the manufacture.


Does a 2005 ES 330 Lexus have a timing chain or belt?

The 2005 Lexus ES330 uses the 3MZ-FE Toyota V6 engine, which has a timing belt.


Where is the fuse box located on a 2005 Lexus es330?

one is under the hood but that's obvious - the other is behind the ash/coin tray - just pull out the door


What are the sizes of windshield wiper blades on the 2005 Lexus ES330?

The 2005 Lexus ES330 takes 24" drivers and 20" passenger side wiper blades. See sources and related links below for more information. Since there are over 22 different wiper arm attachments, do not buy wipers just by length only. Be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment.


How do you replace the license plate bulb on a 2005 Lexus RX330?

Ask your car dealer...


When should you perform a transmission fluid replacement on a 2004 Lexus ES 330?

My 2005 ES330 manual says 60,000 miles,be very carefull of the transmission fluid that is used, book says ONLY Toyota T type 4 trans fluid, only place I could find it was at a Toyota or Lexus dealer,but its not too expensive


How do you set Garage Door Opener On 2005 Lexus ES330?

steps to set the remote control buttons on ES330: 1) close your garage door, set the opener in lock status, 2) push the button of a existed remote control for your garage opener, at the same time push a selected button of the remote controller on your ES330, keep pushing the both buttons for over 15 seconds until there is quick flash happened in your ES330 car's remote controller, 3) push the leaning button in your garage opener once, then a leaning light will flash on the opener, 4) then immediatelly push the selected button of the remote controller on your ES330 once, then push the button again, if the door did not open at this time, you should push the button again. 5) now the you finished the setting on the remote button in your ES330.


How do you replace the fuel filter on a Honda Accord 2005?

You don't. It is a permanent filter mounted inside the fuel tank.


When should you change the timing belt on a 2005 Lexus ES330?

the best time would be for the 80,000 mile service or what ever survive is due before 100,000 miles. If you got the car new you might get reminders in the mail, or look in the owners manual that came with the car. It is always best to get it done before 100,000 miles.


What is the gas mileage for a 2005 Lexus gx 470?

on a 2005 Lexus GX470 milages is 15MPG city and at the most 20MPG highway.


Where was the RX 330 Lexus for 2005 manufactured?

The 2005 Lexus RX330 XU30 series were manufactured at the Toyota Miyata plant in Miyawaka, Fukuoka, Japan.


How do i replace 2005 accord starter?

The starter on a 2005 Honda Accord is replaced by disconnecting the negative battery terminal, removing the starter shroud, and unbolting it from the block. The wiring harness is then disconnected and the replacement starter mounted.