answersLogoWhite

0


Best Answer
Copy

Get a manual on your car from the parts store as you have to work with the air bag and can be sccidentally deployed. Also the wiring for the air bag has to be handeled in a certain way. Or take it to a garage.

*added information* Note that the Chevy s10 production year starts in 1982. You may have mistaken it as 1981 by the label that states production of it within the factory.

User Avatar

Wiki User

โˆ™ 2015-07-15 20:53:41
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace ignition tumbler on a 1981 Chevy S10?
Write your answer...
Submit

Related Questions

How do you replace 1981 Chevy ignition cylinder?

== ==


How do you replace a fuel pump in a 1981 Chevy Celebrity?

Chevy didn't make a 1981 Celebrity


Why is ignition key hot on a 1981 corolla The key will not turn to start. Is it the ignition switch andor the locking barrell assembly.?

replace the ignition swith. replace the ignition swith.


How do you replace the ignition switch on a 1981 Mercedes 300SD?

Remove the retaining ring at the top of your 1981 Mercedes-Benz ignition switch. The ignition switch will slide out. Remove the wiring harness. Reverse the process to install your new ignition switch.


Where is the ignition control located on a 1981 Chevy Blazer?

Depending on what type engine you have, the ignition module may be an integral part of the distributor cap.


Where is the ignition coil on a 1981 Chevy one ton truck?

Mounted in the center of the distributor cap.


How do you replace the ignition switch for a 1981 Chevy pickup?

You have to remove the steering wheele to access a Phillips head screww holding the key switch in place. It has a rack and pinon gear on the end which pushes a rod down when the ignition is turned. you have to get this realigned properly to atart the vehicle. So take your time and don't force it.


Where is the ecm located on a 1981 Chevy Silverado?

no ECM's in a 1981


How do you replace an ignition tumbler on a 1981 Ford truck?

Take your battery cable off the post so you don't short out anything. Turn the key to run and then you have to take the steering wheel off to get to the release pin. When you push the pin you should be able to pull the ignition switch out. If you can't turn the key to run you will have trouble. I just did this and had to drill the ignition switch out which wasn't fun.ANSWER #2 1994 ford f150Replacing ignition tumbler on a ford f150 1994 Memorial day week end and my brother just broke the key off in the ignition of my truck. Ohhh Brother! HOW TO replace the tumbler when a key is broken off or really stuck in the tumbler.First: You need to remove the four philups head screws on the under side of the steering column. Second: you will notice a pin when looking up at the underside to the column. Laying on the seat you will have to position (turn) the lock to a position where it will allow you to depress the pin to slide the tumbeler out. After pressing the button with a nail or nail set or other, you then easily pry the tumbeler out. The tumbeler is about $50 adn yyou can get it at the auto parts store.If you are looking to now get the key on the ignition tumbler to now match the doors well, that's a issues that i do not have an answer for. And to be quite honest, do you really care that much to spend that much $$$ if you have an old piece of shi* like this anyway? If you are really looking to get the keys to match then call a locksmith or order the tumbler from FORD, MAYBE.PLease note that you may be able to slide or pry the key out of the tumbeler after you have removed the tumber. This all depends on how stuck the key really is and secondly, how old the tumbeler is. A penny saved and penny earned is not really the case with this repair. You could just end up breaking a key again and have to read this rant all over again.Paul


Did chevy make a corvette stingray in 1981?

The "Stingray" moniker was not used in 1981.


How do you replace a speedometer cable for a 1981 Chevy Malibu?

you can replace the speedometer by taking it to your nearest car dealers shop/ sale or you can just take it and post it online by taking a picture and people can tell you and give you a bit more information about this ;)


How do you change the fuel pump on a 1981 Chevy Corvette?

== ==


Does a 1981 Chevy have a catalytic converter?

It did when it came from the factory.


How much for a starter motor for a 1981 Chevy?

A 1981 Chevy starter will cost approximately $125. The starter can be found at discount auto-parts stores for as little as $80.


Why won't Mercedes 1981 300D turn off enev when key is removed?

There are vacuum lines in your ignition switch. One of them is leaking or had been pulled loose. If the former is the problem, replace the vacuum line.


What is the freon capacity for a 1981 Chevy Camaro Z-28?

The 1981 Chevrolet Camaro air conditioning system has a Freon capacity of 5.3 pounds. The Freon that was originally used in the 1981 Chevy Camaro is no longer available.


Will a motor for a 2001 Chevy Silverado fit a 1981 Chevy Silverado?

No it will not. total different designed engines.


What size battery for 1981 454 Chevy engine?

Ddd


How much does a 1981 Chevy pickup weigh?

about 6500 pounds.


Where is the thermostat on a 1981 Chevy Malibu w 350?

The 1981 Chevy Malibu 350 engine thermostat is located on the front of the engine. You can follow the water supply hose from the radiator to the thermostat.


1981 firebird ignition key will not turn back from the run position?

Hello... I,m T/A76 and I have 3 T/A,s that have all had that happen...It,s common! The tumbler in the iqnition itself is the problem. All you need is a new iqnition and you can buy them new at Auto Zone,Murry,s,Advanced Auto etc. Basicly anywhere.


What seat belts from other vehicles fit 83 Chevy truck k 20?

any seat belts from an 1981 through1987 Chevy truck or 1981 through 1989 blazer or suburban


What type of transmission came in a 1981 Chevy S 10 2.8L V6 2 wheel drive?

1981-1982 Chevy s-10 with 2.8L V6 automatic transmission TH200C


How do you remove ignition switches on 1981 corvette with t and t'?

To remove the ignition switch in a 1981 Corvette, insert the key into the ignition while leaving it in the "off" position. Insert a straightened paper clip next to the key, turn the key to the "Acc" position, pull the key and clip out together, and place the coil down.


What does a 1981 camaro look like?

Chevy used the same bodystyle for the Camaro, with some yearly modifications, from 1970-1981