Top Answer
User Avatar
Wiki User
Answered 2008-10-01 01:17:17

The hub will need to be removed and the stud pressed or drilled out to be replaced.

User Avatar

Your Answer

Still Have Questions?

Related Questions

Wheel offset for a 1991 Toyota?


How do you change wheel bearings on a 1991 Toyota pickup 2WD?

A wrench

What is the brake light number for a replacement on a 1991 Toyota pickup?

I am looking for the bulb number to replace a burnt out bulb on a 1991 Toyota pickup

How do you replace air filter 1991 Toyota Cressida?

Change a air filter

How to Replace blown light bulbs in 1991 hiace van?

The headlights on a 1991 Hiace van have to be reached through the wheel well of the vehicle. Once the wheel well is removed pull the old bulb from the housing and replace the bulb.

Where is the fuse box located on a 1991 Toyota Celica convertible?

My friend has a 1991 Toyota Celica Active Sports and the fuse box is located inside the car underneath the steering wheel behind a pannel

Where is the fuel filter located on a 1991 Toyota supra?

On Engine, drivers side, under intake. Very tough to replace. Bad Toyota!

How do you remove and replace 1991 Toyota MR2 radiator?

Remove the front bumper to remove the radiator

When should you replace the timing belt on a 1991 Toyota corolla?

every 60 k miles

How do you replace fuel pump on 1991 Toyota celica gt?

You will need to take the fuel tank off the 1991 Toyota Celica GT and remove the fuel pump and replace it. Always make sure to drain the gas before you take the tank off the car.

Where is the compressor located for the airbag suspension on a 1991 Toyota SC400?

The compressor is between the right hand wheel and headlight (right hand drive) in wheel arch

What size is the wheel center bore for a Toyota pickup 1991?

Call any Discount Tire store. They will tell you.

What is the 1991 Toyota pickup wheel offset and bolt pattern?

bolt pattern is 5x114.3 offset is medium high

How do you change the right side wheel bearing on a 1991 lincolin continental?

Do you have to replace it or can you just repack it? It is a sealed hub unit. You have to replace the entire thing.

What transmission came in the 1991 Toyota 4x4?

i have the 1991 toyota 4x4 with a g58 trans

Is a 1991 Toyota 4Runner compatible with a 1990 Toyota 4Runner?

A 1991 Toyota 4runner is bigger than a 1990 4runner

Why is the cooling fan on all the time on my 91 Toyota Corolla?

The 1991 Toyota Corolla cooling fan will stay on all the time if the temperature sensor is malfunctioning. Replace the temperature sensor.

How do you replace the rear lights on a 1991 Toyota Corolla?

go inside the trunk there should be a clip you push that down an pull the assimbly out an replace the burned out bulbs hope this helps you...

What would it cost to replace all four struts on a 1991 Toyota Camry?

I believe about $800 at least with struts only and plus $400 if you want to replace springs too.

Toyota Previa 1991 the light in the insrment does not work all the fuses in the on the dash checks ok so are the swiches?

replace the bulbs

How do you replace the fuse that controls the radio and clock on a 1991 Toyota Tercel?

It is in the fuse box. Check all of the fuses with a test light.

How do you disassemble the hub on a 1991 Toyota 4wd pickup so you can replace CV joint?

Check your local library for a repair manual.

How do you grease rear wheel bearings on a 1991 grand am?

You don't. In the 1991 Pontiac Grand Am, the wheel/hub assembly is pre-built at the factory and as such, can not be disassembled for maintenance. If you are having trouble with lubrication or worn bearings, you must replace the entire assembly.

Does the 1991 Buick century have sealed wheel bearings?

Yes, on Buick Century 1991 you need to replace the whole hub, it is much easier than replacing individual bearings.

What could cause a whirring noise and a vibration on the front passenger side of my 1991 Toyota corolla if it has new struts and tires?

A bad wheel bearing

Still have questions?