open the bonet and locate the bulb from the back of the indicator there is a cable connected to the back of the bulb you must rotate it to remove the bulb. note: some cars u need to pull a little piece of metal o something to release the hole indicator to the front of the vehicle. i hope that help u. cherssss.... Here is what I needed to do on a 1999 A6: The engine air clearner assembly is very much in the way so I removed it. It is relatively easy with basic tools. Working at the front passenger side of the engine compartment remove two small Phillips head screws that hold the engine air inlet duct in place at the top of the radiator support and remove the three duct sections. These come out easily. Use a large screw driver to unclip the 4 metal clips that secure the top of the air cleaner assembly. To move it out of the way I disconnected the electrical connector to the sensor closest to the fender - push in on the metal bail that locks the connector in place and gently pull the connector off. There is one 10mm hex head screw that holds the air cleaner base in place near the right fender. Remove the screw and pull the base of the air cleaner straight up. Now you can easily access the turn signal assembly. You will see a gray, flat plastic piece about 4" long that protrudes in the direction of where the air cleaner assembly was. Gently rotate this bulb holder counterclockwise about a quarter turn. It should come out easily. Replace the bulb with a 2357A. Not every auto parts place carries it so look around and get the right one. This is also a good time to replace the engine air cleaner. The problem may not be the bulb but the metal contacts in the bulb holder. Clean them with a pencil eraser or gently with very fine sand paper. Don't push hard and deform the contacts.
The front turn signal assembly will pop out with a little help. It is held in place by clips that snap it into place.
Under the front panel of the car
First you have to take off the front bumper. Then there are three screws you will have to undo in order to take out the entire headlight housing to then get to the turn signal.
yes you do
pull the steering wheel
On the 1998 Audi A6, the turn signal bulb can be replaced by opening the hood. Reach into the turn signal from the fender wall and push in and turn the old bulb to remove it. Push in and turn to replace with a new bulb.
How do you replace a turn signal bulb in a 1998 cavalier
there located behind the dash below the radio to the left of the ashtray. side by side,hazzard and turn signal
You should be able to go under the hood and remove a cover. This should reveal the back of the light enclosure. Just remove the bulb and replace it with a brand new one.
Replace the turn signal flasher relay.
On a 1998 Volkswagen Passat the starter is located front of the transmission housing. To replace the starter the car needs to be raised so the starter can be reached from underneath the car.
Tutn signal flasher is located on the steering column. Revove the cover that is located between the steering wheel and the instrument panel. The Flasher is yellow. I did not have to replace mine, some wires were loose.
Push in and turn.
If this is a 2.8 V6 the thermostat is located on the front of the engine. Ask 'Where is the thermostat located on a 1995 Audi A6?' on this site and you'll find someone has done a great job of explaining how to find and replace the thermostat.
Open hood panel and prop with rod. Remove screw at headlamp that holds signal lamp. pull lamp straight forward. remove and replace bulb
Where to find flasher on 1998 Lincoln Continential
on my 1999 deville the pump is under the car just in front of the drivers side front tire easy to replace.
You have to replace front and rear bulbs.
how to replace a fuel filter on a 1998 montecarlo how to replace a fuel filter on a 1998 montecarlo
cant be done
The turn signal relay is located on the driver side by the fuse box it is just plugged in like a fuse you just unplugged and insert the new one.
The 1998 Toyota signal relay switch is located below the dashboard, on the drivers side. The signal switch simply plugs in and out.
must replace whole turn signal switch.