Chevy Cavalier

How do you replace the water pump on a 1988 Chevy Cavalier?

8910

Top Answer
User Avatar
Wiki User
2014-10-07 02:13:21
2014-10-07 02:13:21

Drain the radiator on the 1988 Cavalier. Take of the water pump belt. If the fan and shroud are in the way then remove them. unbolt and remove the pump. Bolt up the new pump and put the belt back on. Put the shroud and fan on if they were removed. Fill the radiator back up.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the water supply hose from your 1988 Chevy Cavalier thermostat housing. Remove the thermostat housing bolts. Lift the old thermostat out and drop in the new thermostat.

User Avatar

Yes, I have a 1988 and 1989 Chevy Cavalier Z24 and they both have the 2.8L V6

User Avatar

1988 chevy cavalier flasher take ash tray and bracket out look up and lift you can see it if not you can put your hand up in to lift and find it.

User Avatar

i would just get the entire drive axle..do it your self, it may ba alot cheaper.Hope this helps

User Avatar

The Hazard flasher button for a 1988 Cavalier can be bought from several sources. A Chevy dealer, online parts sites or even local salvage yards can all supply the button.

User Avatar

1-6-5-4-3-2- good luck ......chevy boy

User Avatar

I won't swear to it, but it should be .045. That is for a 3.1L engine.

User Avatar

Remove the wiring harness from your 1988 Chevy Cavalier fuel pump. Remove the fuel lines from the fuel pump. Remove the fuel pump retaining bolts. Reverse the process to install the new fuel pump.

User Avatar

The 1988 Chevy Cavalier spark plug wires are quite easy to remove. The spark plug wires simply pull off on each end. Put the new spark light wires on by pushing downward on each end.

User Avatar

The 2.8 litre (2800cc,173 cu.in.) 60 degree v6 in a 1988 Chevrolet Cavalier z-24 was factory rated at 130 HP, torque came in at 160 ft. lbs.

User Avatar

How do you replace the water pump on a 1988 Cadillac Seville?

User Avatar

The 1988 cavalier and or jbody cars use a coil pack.You do not have a distributor and if a ignition issue is present replacing one or all coil packs are the answer.I originally stated it could have had a distributor but,was incorrect on my first response.As said if you replace the coil packs unhook your negative battery cable prior to any electrical work to prevent and problems and safety.

User Avatar

its under the car by the gas tank easy to get to from the back of the car.

User Avatar

Drain the water from your 1988 Chevy Corvette cooling system. Remove the water supply hose from the top of your thermostat housing. Remove the thermostat housing bolts. Remove the thermostat. Reverse the process to install the new thermostat.

User Avatar

If I had to replace a fuel line I would get a replacement out of a car in a wrecking yard and install that.

User Avatar

I just want to know when do i have to replace the water tank.

User Avatar

the speed sensor is located on top of the transaxle near where the right side drive axle is attached . remove the two wire electrical connector and the retaining screw and pull it out. reverse the procedure to install.

User Avatar

It should be .045 of an inch. there should be a sticker on the fie wall or under the hood to confirm

User Avatar

cylinder? key? switch? fuse? module? what are you talking bout?


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.