0
- Insert Key
- Do not press clutch / brake
- Press Start button
- Wait until the Car / revelant Service symbol disappears on the Rev counter display
- Immediately after the symbol goes out - Press and hold Both buttons on the Rev Counter
- Continue to hold - the system will run a dash light check
- Continue to hold
- Display will then show VIN / Menu, - continue to hold through this until the time Reappears on the display.
- Now release Only the Right hand Button (trip reset) for about a second, and then press and hold again (whilst still holding the LH button)
- After another second or 2 the display will show the Front Brake Symbol You Are
- Now in the Service Menu
- Use the BC Button (on indicator stalk) to scroll through to the relevant symbol - eg Oil Reset or Rear Brakes
- To Reset the warning indicator light - Press & Hold the BC Button at the revelant symbol until RESET appears - then press and hold again until the process is complete.
- Turn Off and On the Ignition again - Warning should now have gone!
What else can I help you with?
How do you reset 2008 Honda Element service light?
How do you reset 2008 honda element service light?
How do you reset service indicator on 2008 Mercedes 109cdi?
take a hammer to the light
How do you reset the tire pressure warning light on a 2008 dodge Caliber?
The light will reset itself if the system is working properly and the tires are at the correct pressure. If the pressure is correct and the light is still on, you need to take it in for service.
How do you reset engine light in 2008 buick lucerne?
how do you reset check engine light in 2008 buick lucerne
How do reset t-belt light cruiser 2008?
Hi I have cruiser 2008 gxr how is reset t.belt light
How do you reset the service indicator light on a 2008 Renault mascott van?
To reset the service indicator light on a 2008 Renault Mascott van, first, turn the ignition key to the "ON" position without starting the engine. Then, press the accelerator pedal three times within 10 seconds. Turn the ignition off, and the service light should be reset when you turn the ignition back on. If the light remains on, you may need to repeat the process or consult the vehicle's manual for specific instructions.
How do reset service light on a 2008 volkswagen r32?
Resetting a service engine light on a 2008 Volkswagen r32 requires a diagnostic tool to be done properly. Another way requires disconnecting the battery for 5 seconds or more.
How do you reset the service light in a 2008 Volvo s40?
I used this procedure to reset my 2002 s40 services light (it should work for 2008 s40 also). a) insert ignition key and turn it to the 1st click - no lights on bottom of the instrument panel should be light up b) press and hold trip odometer reset button, and turn the ignition key to the 2nd click - the row of lights at the bottom of the instrument panel should come on c) after about 5 secs the lights should go off except the Service reset light - it will blink d) when the Service reset light has blinked for about 3 times - release the odometer reset button e) the Service reset is complete Note: This procedure cannot be used to reset Check Engine light - it requires an OBD2 code reader.
How do you Reset Maintenance Warning Light on a 2008 Toyota 4Runner?
How to Reset Maintenance Warning Light on a 2008 Toyota 4Runner
How do you reset service light on 2008 Audi a3 tdi?
Resetting an 2008 Audi A3 TDI service light can be done two ways. One by addressing the problem and the other way is to unhook the battery cables for up to a minute.
How do you clear the service engine soon light in a 2008 Nissan altima?
if your take it to a autozone tell them you have a check engine light and they will tell you whats wrong if anything and reset it take it to autozone and tell them your check engine light is on and they should reset it
How do you reset service light seat ibiza 2008?
Try This Press and hold the trip reset button. Turn on the ignition while still holding the trip reset button you will hear the normal beeping noise. Hold trip reset button until the service tool (little spanner) disappears and 3 dashes appear (- - -). You can now release the button and the service interval/oil change light is reset Alison Bostock
