answersLogoWhite

0

SHARP

Instruction Manual & Warranty

Power reguirement:

One 3v Lithium Battery CR2032 is required to hold the,time memory. The lithium battery is included.

Two "AA" Alkaline batteries are required to operate the time function. These batteries are not included.

Time Zones:

H-Hawaii-Aleutian Standard Time

A-Alaska Standard Time

P-Pacific Standard Time

M-Mountain Standard Time

C-Central Standard Time

E-Eastern Standard Time

Setting Procedure for the Accu-Set Clock:

Before inserting the 2 JlAA" batteries into the battery compartment:

1) The clock hands need to be at the 12:00 position. If the hands are not all ready set at 12:00 you

can turn the black dial on the back of the clock to manually set the hand to the 12:00 position.

2) The MODE switch (8) should be in the SET position.

3) Slide the Time Zone switch (2) to the correct time zone,

4) Slide the DST switch (9) to the appropriate position for your area.

5) Verify that the rear LCD Display (4) reads the correct time.

6) Once all above is complete, insert the "AA" batteries; slide the MODE switch (8) to the run

position, the clock will fast forward to the correct time.

-When the "AN' batteries are low the clock will stop at 12:00 indicating you should replace the "AN'

batteries. Alow-battery icon may also show on the rear LCD Display (4) and the LCO display will

appear dim.

Note: To change the Time zone, OST, or time, the MODE switch (8) must be in SET position. Remove

the "AN' batteries, and then follow the setting steps above.

Daylight Savings Time:

-If you live in an area that does observe OST, place the OST switch into the ON position. The clock will

now adjust automatically each spring and fall to correct for the 1-hour time change.

-If you live in an area that does not observe OST, such as Arizona, Hawaii, or parts of Indiana, place the

switch into the OFF position to deactivate the OST function.

Replacing 3V Lithium Battery:

The Accu-set time memory is maintained by a lithium button cell battery, model CR2032. The expected

life of this battery is about 8 years, Be sure that the 2"AN' batteries in the clock are fresh. The MODE

switch (8) must be in the RUN position when replacing this button cell battery, This battery is located in

the small round battery compartment on the rear of the clock secured by a screw. Open the Battery

Compartment (3) with a screw driver and replace the CR2032 lithium battery observing the polarity,

Then close the compartment securing with the screw.

Setting the correct Data information in the LCD display:

1} Manually turn the clock hands to 12:00.

2} Be sure a fresh Lithium button cell battery is in place, model CR2032.

3} Slide the Time Zone switch (2) to the desired time zone position.

4} Choose DST on or off, by sliding the DST switch to ON or OFF position.

S} Slide the MODE switch (8) to SET position, a SETUP icon will be flashing on the display. The Hour digit

will be also flashing. Press (+) Key (6) or (-) Key (7) to adjust to the correct hours. Note the "PM"

indicator on the LCD display.

6) Press MODE key (5) once, the minute digit will be flashing. Press (+) key (6) or (-) key (7) to adjust to

the correct minutes.

7) Press MODE key (5) again, to set month, day, year, similarly.

8) Insert two fresh "AA" alkaline batteries into Battery Compartment (1), according to the polarity

shown.

9) You can slide the MODE switch (8) to SEC position, press (+) Key (6) to have the clock's second hand

move to 12:00 position.

10) Slide the MODE switch (8) to RUN position, the clock's hands will move quickly, and automatically

synchronize the new time data in the LCD display.

Replacing the "AA" batteries:

For best performance, replace the "AA" batteries annually to maintain accuracy. With the Mode switch in

the RUN position, remove the old "AA" batteries. Make sure the hands are in the 12:00 position. If not so,

Manually turn the hands to 12:00. Insert 2 fresh "AA" alkaline batteries into the Battery Compartment (1)

according to the polarity shown. The clock will automatically move to the correct time displayed in the

LCD display. Alkaline batteries are recommended. Carbon zinc and rechargeable (nickel cadmium)

batteries are not recommended. Please help in preservation of the environment and return used batteries

to an authorized depot.

For Customer Service Please Call Toll Free at

1-(800)-221-0131 and ask for Customer Service.

Monday-Friday 9:00 AM - 4:00 PM EST

Please call for assistance before returnin the clock to the store.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you set a Sharp Accu-Set Round wall clock model SPC991?

To set the Sharp Accu-Set Round wall clock model SPC991, first ensure the clock is powered on. Press and hold the "SET" button until the hour digits begin to flash. Use the "HOUR" and "MINUTE" buttons to adjust the time accordingly, and then press "SET" again to confirm the changes. The clock will automatically synchronize the time after setting.


How do you set outdoor temp on SPC 1003 sharp atomic clock?

how do you change the day of the week? model spc1003


How do you set a Sharp Accu-Set Clock Model SPC991?

Ah, setting a clock can be a peaceful experience, my friend. To set your Sharp Accu-Set Clock Model SPC991, gently locate the "Set" button on the back or bottom of the clock. Press and hold it until the time starts blinking, then use the "+" and "-" buttons to adjust the hours and minutes. Finally, press the "Set" button again to lock in your chosen time. Just like painting a happy little tree, take your time and enjoy the process.


How do you set the time on sharp accu-set clock model spc991?

To set the time on a Sharp Accu-Set clock model SPC991, first, locate the "Time Set" button on the back or bottom of the clock. Press and hold this button until the time display starts blinking. Use the "Hour" and "Minute" buttons to adjust the time to the correct hour and minute. Once the time is set, release the "Time Set" button to save the new time.


How do You turn off the alarm on a Sharp atomic clock?

To turn off the alarm on a Sharp atomic clock, locate the alarm switch on the back or side of the clock and set it to the off position. Depending on the model, you may need to press a specific button or sequence to deactivate the alarm. Refer to the user manual for detailed instructions.


How do you set the clock S10 Scan Atomic Clock?

How do you set the time on a S10/Scan atomic clock model 86715


How to set a sharp clock SPC486A?

When u press the set button it will go to each thing u need to set like hour min alarm date etc. Use the +- buttons to set the correct info then hit set again to lock it in and go to the next thing to


How do you set time in digital clock ajanta odc?

how to time set up ajantha degital clock model no: olc 103


How do you set atomic clock model 88902?

To set the atomic clock model 88902, typically you'll need to press and hold the "SET" button until the clock enters setup mode. Then use the arrow buttons to adjust the hours, minutes, and other settings as needed. Refer to the clock's manual for exact instructions on setting up your specific model.


How do you set a sheng bang model hd 1688 clock?

It should set itself.


How do you set your sharp spc026 alarm clock?

first throw it out the window then get it do it again if its not at correct tine


How do you set the day on a sharp spc900 atomic clock?

To set the day on a Sharp SPC900 atomic clock, you typically need to press the "Mode" button until the day setting starts flashing. Then, you can use the "+" and "-" buttons to adjust the day to the correct setting. Once you have selected the correct day, you can press the "Mode" button again to save the changes and exit the setting mode. Make sure to consult the clock's manual for specific instructions tailored to your model.