0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you test ignition coil on your Alero 1999?
1999 Alero how do i test ignition coil pack
How do you test a small engine ignition coil on a 22 hp kohler while the coil is not installed?
You can't test a coil off the unit the only way to test the coil is disable the kill circuit if it fires it mean u have other problems such as a safety switch problem like seat switch or neutral safety switch. The above answer is completely false. You use an ohm meter and test to manufacturers specs for the ohm of your specific coil, typically in the 8,000 ohm range +/- 2,000 ohms. Save
How do you test ignition coil on 2005 trailblazer ls 4100?
let the engine running, lift off the ignition coil one by one after opening the screw...a tick sounds will be heard ... no tick sound and gasoline leak on the plug thread means the ignition coil is busted.
How do you test a ignition coil with circuit diagram?
You cannot test it with a diagram. You will need a multimeter to test the coil. Click the link.
How do you test ignition coil Volvo s70?
pluginyerarse
How do i test the ignition module in my 1984 Ford Laser?
There is no ignition module in a '84 laser. They have a coil and distributor unless it has been modified. If you don't get a spark across the points in the distributor when you try to start the engine you probably need a new coil.
How do you test the ignition coil on a 1994 acura integra?
ohm it.
How do you troubleshoot the wiring for an ignition coil I have a 1988 jeep comanchee with a 6 cyl. engine Cranked and ran fine one day wouldn't start the next Am getting no spark from ignition coil?
test for power before the coil, if you have power change the coil, if not trace the wires back and check for broken parts or bad connections.
How do you test a lawn mower ignition coil?
Remove the kill wire from the ignition coil. It's the only wire that doesn't go to a plug. Remove one of the spark plugs. Reconnect the plug wire to the plug that has been removed. Make sure the threads of the plug are touching metal on the engine somewhere. Crank the engine. Should see spark. If not, bad coil.
Can you view wiring diagram of ignition system F 150 1987?
Hope This Help.TESTING Ignition Coil TestThe ignition coil must be diagnosed separately from the rest of the ignition system.Primary resistance is measured between the two primary (low voltage) coil terminals, with the coil connector disconnected and the ignition switch off. Primary resistance should be 0.3-1.0 ohms.On Dura Spark ignitions, the secondary resistance is measured between the BATT and high voltage (secondary) terminals of the ignition coil with the ignition OFF , and the wiring from the coil disconnected. Secondary resistance must be 8,000-11,500 ohms.If resistance tests are okay, but the coil is still suspected, test the coil on a coil tester by following the test equipment manufacturer's instructions for a standard coil. If the reading differs from the original test, check for a defective wiring harness.Ignition Coil Primary Circuit SwitchingInsert a small straight pin in the wire which runs from the coil negative (-) terminal to the TFI module, about 1 in. (25mm) from the module.WARNINGThe pin must not touch ground!Connect a 12 VDC test lamp between the straight pin and an engine ground.Crank the engine, noting the operation of the test lamp. If the test lamp flashes, proceed to the next test. If the test lamp lights but does not flash, proceed to the Wiring Harness test. If the test lamp does not light at all, proceed to the Primary Circuit Continuity test.Ignition Coil ResistanceRefer to the General Testing for an explanation of the resistance tests. Replace the ignition coil if the resistance is out of the specification range.Ignition Coil Secondary VoltageDisconnect the secondary (high voltage) coil wire from the distributor cap and install a spark tester between the coil wire and ground.Crank the engine. A good, strong spark should be noted at the spark tester. If spark is noted, but the engine will not start, check the spark plugs, spark plug wiring, and fuel system. If there is no spark at the tester: Check the ignition coil secondary wire resistance; it should be no more than 5,000 ohms per foot. Inspect the ignition coil for damage and/or carbon tracking. With the distributor cap removed, verify that the distributor shaft turns with the engine; if it does not, repair the engine as required. If the fault was not found proceed to the Ignition Coil Primary Voltage test.Ignition Coil Primary VoltageAttach the negative lead of a voltmeter to the distributor base.Turn the ignition switch ON and connect the positive voltmeter lead to the negative (-) ignition coil terminal. Note the voltage reading and turn the ignition OFF . If the voltmeter reading is less than 90 percent of the available battery voltage, inspect the wiring between the ignition module and the negative (-) coil terminal, then proceed to the Ignition Coil Supply Voltage test.Ignition Coil Supply VoltageAttach the negative lead of a voltmeter to the distributor base.Turn the ignition switch ON and connect the positive voltmeter lead to the positive (+) ignition coil terminal. Note the voltage reading then turn the ignition OFF . If the voltage reading is at least 90 percent of the battery voltage, yet the engine will still not run; first, check the ignition coil connector and terminals for corrosion, dirt, and/or damage; second, replace the ignition switch if the connectors and terminal are okay.Connect any remaining wiring.REMOVAL & INSTALLATION Carbureted EnginesDisconnect the battery ground.Disconnect the two small and one large wires from the coil.Disconnect the condenser connector from the coil, if equipped.Unbolt and remove the coil.Installation is the reverse of removal.Fuel Injected EnginesSee Figures 1, 2, 3 and 4Fig. Fig. 1: Disengage the high tension wire by pulling on the connector boot-fuel injected enginesFig. Fig. 2: Separate the wiring harness connection at the coilFig. Fig. 3: Unscrew the coil from its bracket mountFig. Fig. 4: Remove the coil from the enginePulling on the connector boot, disconnect the high tension lead at the coil.Disconnect the wiring at the ignition coil.Remove the ignition coil-to-bracket attaching screws, then remove the coil.To install:Install the coil, tightening the screws to 25-35 inch lbs. (2.8-4.0 Nm).Connect the ignition coil wiring harness and the high tension lead.
How do you test a Geo Metro 1995 ignition coil?
A 1995 Geo Metro ignition coil is tested by measuring the resistance across the coil. If it exceeds the manufacturer's recommendation, it must be replaced.
Would like info on ignition troubleshooting for 92 Chevy Suburban?
test ignition coil,ignition module,pick-up coil,electronic spark control,and knock sensor
