0
Use a multimeter or digital multimeter and set it to the ohmmeter mode. Put the test leads on the speaker terminals. It won't be perfect, but if it says 1.8 ohms or so then it's a 2 ohm speaker.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What ohm speaker is best?
take a 2 ohm bridge into 1 ohm
What is the difference between a 8 ohm speaker and 12 ohm speaker?
Study ohms law to get your head around it.
How do i Make a 8 ohm speaker 16 ohm?
You can't change the ohm load of a speaker. What you can do, is get a second 8 ohm speaker to run with that speakers in series and you will get a total ohm load of 16 ohms.To run them in series, simply wire the positive terminal of one speaker to the negative of the other speaker. One speaker will have an open positive terminal which you wire to the positive terminal on the amp, and same goes for the negative on the other speaker (to the amp's negative terminal of course).
Can resistance be added to speakers to make a 4 ohm speaker have an 8 ohm load?
You "can" add a four ohm resistor in series with a four ohm speaker, and make it look like an eight ohm speaker, however, the frequency response will not be the same. It is better to use to correct speaker for the amplifier, or use two four ohm speakers in parallel. That resistors power rating must exceed the rating of the speaker. Half the from the amplifier will go to the speaker, while half will go to the resistor, making it get quite hot.
Will an 8 ohm speaker work with an 6 ohm amplifier?
Yes, but it will not be as loud as it would have been had a 6 Ohm speaker been used. Byt the way, the word 'Ohm' is capitalized, because it was someone's name.
How do you make a 16 ohm speaker 8 ohm?
You cannot make a 16 ohm speaker into an 8 ohm speaker. You would need to replace the voice coil. You can, however, put two 16 ohm speakers in parallel, and the equivalent impedance would be 8 ohms. The only remaining issue is frequency response, and that's a factor of speaker and enclosure design, so best is to use the exact speaker as originally designed.
What is the ohm's on Chevy Colorado speaker?
4 Ohms. Can use any standard 4 Ohm speaker as long as you don't chassis ground it.
2 ohm speaker dvc in series?
That would yeild a 4 ohm load
If an amp runs 1000 w rms at 1ohm how do you wire a dual 4 ohm speaker to run at 1 ohm?
the impedance of a speaker is a characteristic that is has. A 4 ohm speaker will always have a 4 ohm impedance and it cannot be changed. If 2 speakers of 4 ohm impedance are wired in parallel, then the total impedance will be 2 ohms. Similarly, if you wire 4 speakers together, the total impedance will be 1 ohm. Wiring a 2 ohm speaker to an amplifier rated to drive a 1 ohm load should work without any problems but expect the total power output to be somewhat lower than with a 1 ohm load.
Can you replace an 8 ohm speaker with a 4 ohm speaker?
Only if your amplifier is capable of driving a 4 ohm speaker. Some have a switch on the back to select 4 or 8ohm speakers. Details should either be printed some where on the back of the amp or the instruction manual
How many ohms would 2 16 ohm speaker cabinets and 1 8 ohm speaker cabinet calculate out to be?
If wired in parallel then 4 ohms.
Can you connect a 8 ohm speaker for a amp designed for a 4 ohm load?
You can, but the available power will only be about half of rated, and the frequency response will be slightly different. Better would be to connect two 8 ohm speakers in parallel, making an equivalent 4 ohm speaker.
