0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you warp a cricket loom?
you can warp a cricket loom one of two ways: Direct method or Indirect method.Direct Warping (courtesy of freehavenfarmltd on youtube)Indirect Warping (courtesy of various sources)measuring the warpPaulina, weaver from San Juan from aldea on Vimeo.FROM SCHACHT SPINDLE COMPANYIndirect Warping Using a Warping BoardFor this method, a warping board is used to measure the warp. The warp is first measured on the warping board and then brought to the loom for threading.Set up a guide stringStep 1. Determine which pegs of the warping board to use by cutting a piece of string a few inches longer than the length of one warp thread. Use a string that is a different color than your warp yarn.Tie one end of the string to a peg and work back and forth around the pegs until the string runs out. Adjust the starting point until the end of the guide string comes out even at the set of 2 pegs marked x in figure 11.Measure the warpStep 2. Tie the end of the warp yarn to the starting peg. Wind back and forth across the warping board following the guide string until you reach the ending two pegs. Wind a figure-eight around these (figure 12). This is the cross and its purpose is to keep the warp ends in order. Wind back to the beginning peg. You have now measured 2 warp ends. Continue following this path until the total number of warp ends are measured.Figure 10: tie the warp ends to the front apron rodFigure 11: Wind the warp Figure 12: Continue and wind the warp back in the reverse direction Remove the warp from the warping boardStep 3. Secure the cross by tying it loosely with contrasting yarn in five places (figure 13) using overhand knots. Now tie choke ties along the warp at about 18" inch intervals. Tie these tightly with a bow tie. Choke ties keep the warp from tangling. After the warp has been tied, remove it from the warping board. Cut all the loops on the non-cross end and tie the end of the warp bundle in an overhand knot.Thread the heddleStep 4. Wrap the warp around the front beam so that it extends about 10" past the heddle.Step 5. Place the heddle in neutral. Find the center of the heddle and then measure out to one side half the width of your warp. (For example, if your warp is 10" wide, measure out 5" and begin threading at this point.)Step 6. Hold the cross in one hand so that each section is separated (figure 14), and then cut the loops at the end and the five ties holding the cross. Notice that the threads stack up Lincoln-log style. Take the top end and use the heddle hook to thread it through the slot at the outermost edge of your weaving. Take the next thread and thread it through the adjacent hole. Alternately thread slot, hole, slot, hole until all warp ends are threaded.Step 7. Tie groups of about 1" of warp ends in overhand knots across the entire warp. Then tie each group around the back apron rod and secure this knot by tightening it up to the first knot (figure 15).Wind the warp onto the warp beamStep 8. Begin cranking the warp onto the warp beam in a clockwise direction. Remove choke ties as they approach the heddle.Step 9. When the warp has been rolled around the warp beam once, insert heavy paper between the layers of warp to separate them.Step 10. Continue winding on, stopping every so often to pull hard on the warp bundle to tighten the warp on the warp beam.Figure 13: Tie the cross Figure 14: Hold the crossFigure 15: Tie the warp to the back apron rod Step 11. Stop winding when there is about 10" of warp left in front of the heddle.Tie onto the front apron rodTie onto the front apron rod in the same way as for the direct method (step 15, figure 10, page 7).
What the procedure of final tie-in pipeline gas?
That depends on whether or not the connection to the new line is going to be the same size as the existing or if it is going to be a maximum of 1/2 the existing line size.
How to tie new wooden wall to existing brick wall?
Just attach using screws through the new timber frame into plastic plugs in holes in the wall.
Where do werewolf's clothes go when they transform in new moon?
They are meant to tie onto the werewolves leg. OMG i love twilight x
Add new gfci from an existing switch?
Find the Hot side of the switch (Where there is voltage regardless of position of toggle on switch). Tie in new Black wire to GFCI. On wire nut with white wire tie in new white wire to GFCI. Do the same for the bare ground wire, if there is one.
Where do you find the fuse box to hook wires to a boat on a 2004 Ford Expedition?
Tie the wires on the new plug into the existing brake and turn signal wires.
What is a Word for to tie a new knot?
To 're-marry' is to tie a new knot...
What month or day rhymes with new tie?
June and July rhyme with new tie.
How do you catch a snapping turtle in your pond?
u can take a milk jug and tie about a foot of line onto the handle and then tie a hook with a 1" gap between the barb and the main shaft of the hook. then tie 6' of nylon string onto the handle and the other end onto a weight that is atleast 3 lbs, or use something that will get caught in the muck of a pond(I use brink for anchors, or rocks).
How much does a railroad company pay for a new treated railroad tie?
$58.00 a tie.
What is the first thing you should do after achieving a boat onto a trailer?
Tie it down so it doesn't get away.
How do you replace outer tie rod on 1994 Subaru?
Remove wheel and properly support vehicle and wear safety glasses. Remove coter pin, loosen tie rod nut a few turns. Use small sledge hammer to strike steering knuckle where it holds tie rod until tie rod becomes loose. Loosen nut that secures tie rod to the inner tie rod. Remove tie rod and count how many turns it takes to remove. Instal new tie rod onto inner tie rod with as many turns as it took to remove old part (secure inner tie rod when turning outter), this will help with alignment. Properly secure outter tie rod to steering knuckle. Install grease fitting (if applicable) and grease, and put wheel on. Get an alignment and your done.
