answersLogoWhite

0


Best Answer

Install a 50 amp breaker in the 100 amp panel and run appropriate size wire to the sub panel connectors...

<><><>

As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.

Before you do any work yourself,

on electrical circuits, equipment or appliances,

always use a test meter to ensure the circuit is, in fact, de-energized.

IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY AND COMPETENTLY

REFER THIS WORK TO QUALIFIED PROFESSIONALS.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

12y ago

Home owner big job

Adding a sub panel is a complicated job in as much as you have to know wire sizes, ampacity of wires and proper electrical workmanship. Such a project should be left to a licensed electrical contractor to take out the proper permits and call for proper inspections. By taking this route it will leave you confident that if any mishaps happen to the installation down the road your insurance company will be behind you 100%.

In an average home a 100 amp panel can used up to 55 amps at any one time during certain periods through out the day. There is a way to extend the bus with conductors of the same size as the distribution panel's bus bars. Discuss this option with your electrical contractor.

If you opt for a panel change, have a 200 Amp 42 circuit board installed. The labour costs are about the same as a smaller board, just the material costs are higher.

<<>>

how do you know how to properly size a sub panel?

example:

100 Amp service panel is full...I understand that I will never use the FLA full load amp

rating of this panel but i want to be able to accurately size the sub because i am going to install a hot tub that requires a 50 amp breaker...

This answer is:
User Avatar

User Avatar

Wiki User

11y ago

You put two 50Abreakers in the 100Apanel and feed each subpanel with conductors from one 50A or the other (i.e., two hot conductors, a neutral and a grounding conductor). There are specific rules about whether the subpanel may need its own grounding rod connection as well, depending upon whether it's in the same building, among other things.

You may optionally place another 50A breaker in each subpanel as a "main disconnect" for circuits fed from that subpanel.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you install a 50A sub panel to a 100A box?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What cause the Main Breaker trips when I start a 30KW 3-phase Motor(Star Delt Starter)?

The wiring is like this:[[30KW Motor ---- Star Delt Starter(100A Breaker inside) ----- 200A Breaker------50A Breaker(Inside the breaker box which located inside the factory) -----100A Main Breaker]]Once I try to start the Motor, the Main Breaker trips immediately.


My seimans elect panel box let me put in tandem breakers?

I wnt to install a tandem breaker but my panel box won't let me. Why?


Is it unsafe to have 60A service going into a new electrical box designed for 100A?

Its not recommended because your new main breaker will allow up to 100 amps and your old wire can only safely handle 60amps. If you put a 60amp main breaker in the new box, that would be acceptable. No, it is perfectly safe. Because the box is overrated, there is no problem. If the box is the main panel, and not a subpanel, install a 60A main breaker so you cannot overload your service. If it is a subpanel this 60A breaker should be in the main panel.


You are building a new home and want to install a 60circuit panel box but electrician says no?

See Discuss Question page below.


How do I set up a security alarm control panel for my home?

You can set up a security alarm control panel by wiring it up to your original electric box or you can have a professional install it for little or no money.


How do you hook up a three prong outlet for an electric stove with a 50A outlet?

This is a common topic here. Firstly, if you are installing new work go with a 4 prong oven outlet. 3 prong outlets are old and do not meet code for new work. To install, you need to run 6/3 romex wire from your main panel to your new outlet. Install the new outlet in a box behind your oven. Wire up the 6/3 in the panel to a 50A 240V breaker. Remember the color code: Black/red/brass screw is hot, White/silver screw is neutral, bare wire/green screw is ground. I also recommend buying a book on Home Electricity repairs. It will show you how to do it right and serve as a handy reference during the job. As always, do it right or hire someone to do it for you. Negligence is fatal with electricity.


How do you install a hot water heater with a designated line to the panel box?

If you don't know that, should you really be doing this potentially dangerous job.


How do you install a 110v receptacle from a 3 phase breaker box if there are no neutrals in the breaker box?

If there is no neutral available you cannot, unless you use an autotransformer and derive a neutral. A panel with no neutral is called a power panel and is used to supply 240 single and three phase loads.


How do you get check engine light to turn off after you install air intake?

.The check engine light can be reset, after you install a new air intake, by removing the instrument panel fuse. The fuse can be located in the fuse box


Can you box in an electrical panel in an open room?

That depends on what you mean by "box in". You must always provide access to an electrical panel.


What is the max amps for a 4 gauge wire can 4 gauge feed a 100A breaker box?

Yes, # 4 AWG copper and 100 amps is the max.


Where is the fuel pump relay located on 2001 ford sport trac?

Inside fuse box under hood, drivers side, near the hood hinge. Slot 50A.