The three phase supply first has to be connected through a three phase safety disconnect switch. From the safety switch the three phase supply then connects to the terminal strip that is supplied in the air conditioner's control panel. The air conditioner unit is factory wired so that all that is needed in external connections if the power and thermostat control.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
If you have a 4-wire receptacle it is likely 240 Volts and one would hope that you are connecting a 240 V AC unit. A typical 4-wire receptacle will have two hot terminals (Usually red and black), a Common terminal (White) and a Ground Wire (Bare or green).
If you have a 220 V AC then you need to connect to the two Hots to get 220 and connect ground to ground. If your AC was 120 V you just need one leg of 240 V so you would connect to Black, White and Ground.
A 30 HP 200 three phase motor draws 92 amps. This supply is going to need a feeder right back to the three phase electrical distribution panel. The first question can this much load be added to the distribution. This is a complicated job in as much as you have to know wire sizes, ampacity of wires and proper electrical workmanship. Such a project should be left to a licensed electrical contractor to take out the proper permits and call for proper inspections. By taking this route it will leave you confident that if any mishaps happen to the installation down the road your insurance company will be behind you 100%.
If an air condition is single phase, then it can only be connected to a single phase source. Since any two legs of a three phase source are considered single phase, there is no conflict, except to note that the individual phases of the three phase source match the voltage requirement of the air conditioner.
NO! The voltages available in the 3-phase system are 480 (if you wire phase to phase) and 277 (if you wire phase to neutral) Don't try it!
Single phase connection has 1 phase wire and a neutral wire. Another wire for protective earth. In three phase system, motor can be connected in star or delta. Most AC induction motors are in Delta. Power distribution system is generally 3 phase 4 wire. Transmission system is 3 phase high voltage. Industry uses 3 phase system, where as 1 phase is for domestic, commercial applications. Both 1 and 3 phase system has a frequency. It is either 50 Hz or 60 Hz, depending upon the country or region.
You can divide a three phase service into (3) single phase circuits providing you have a 4th neutral wire.
5000 volt
If an air condition is single phase, then it can only be connected to a single phase source. Since any two legs of a three phase source are considered single phase, there is no conflict, except to note that the individual phases of the three phase source match the voltage requirement of the air conditioner.
of all of dem 3 phase 3 wire is most economical as it uses less conductor dan in 4 wire system, 3 phase 3 wire is used in transmission and 4 wire in distribution as it has 3 live and one neutral wire. 3 phase needs lesser conductor size than 2 phase 4 wire for the same power. 3 wire dc feeder is more economical than 2 wire dc feeder for the same power. that was all i cud get..... hope u find it a lil helpful.
3
If single phase - 2 wire service > two wires If single phase - 3 wire service > three wires If three phase - 3 wire service > three wires If three phase - 4 wire service > four wires US residential service is usually single phase 3 wire service: Two hots and neutral.
STAR connection is best suit for 3 phase 4 wire seviceas there is a neautral wire is there in this connection
NO! The voltages available in the 3-phase system are 480 (if you wire phase to phase) and 277 (if you wire phase to neutral) Don't try it!
Look for directions on the air-conditioning device and you will see how many amperes it spends. I believe that is 10 A on average.
Single phase connection has 1 phase wire and a neutral wire. Another wire for protective earth. In three phase system, motor can be connected in star or delta. Most AC induction motors are in Delta. Power distribution system is generally 3 phase 4 wire. Transmission system is 3 phase high voltage. Industry uses 3 phase system, where as 1 phase is for domestic, commercial applications. Both 1 and 3 phase system has a frequency. It is either 50 Hz or 60 Hz, depending upon the country or region.
You can divide a three phase service into (3) single phase circuits providing you have a 4th neutral wire.
5000 volt
How do u wire a 1 to 3phase rotoverter
Check the following............... 1. Freon system level. 2. Pressure switch. 3. Clutch wire harness. 4. If above are okay then scan the vehicles computer.