12v 1.5amp power adapter is 18 Watt, can't load more than 18W power consumption,3amp power adapter can load 36W.
Possibly, but not if you want to invalidate the warranty to your appliance.
nope! that would ruin your stuff plus amps is what actually powers appliances so if you dont have enough it wont power up (amps is another word for current)
Probably yes. The 12v 2 amp adapter can put out 12x2=24 watts. The 60w adapter can handle more than twice the power (60 / 12 = 5 amps). However, the voltage of inexpensive adapters may be quite a bit higher under low loads. I'd check and make sure the voltage was not very much greater than 12 volts with a 2 amp load.
No, it is not recommended to substitute a 12 volt 0.5 amp AC adapter with a 7.5 volt 1 amp adapter. The voltage and amperage ratings need to match the requirements of the device you are powering. Using a lower voltage adapter may not provide enough power, and using a higher voltage adapter can potentially damage the device.
no, it may damage the appliance.1Can_12V_2A_adapter_be_used_for_12V_1A_device, 2a adapter cannot be used for 12v, 1a device if the so mentioned parameters are input parameters of the device.Yes, a 12 volt 2 amp adapter has more that enough capacity to operate a 12 volt 1 amp device. In fact the adapter can operate devices up to a limit of 12 volts 2 amps. A device larger than 2 amps connected will tend to heat the adapter up and eventually cause it to fail.
Possibly, but not if you want to invalidate the warranty to your appliance.
No, you need at least a 1.5 amp power pack.
Youshould not parallel two DC output adaptors. If you meant to say that the second device needed an input of 12 V at 2 amps then the 12 V at 3 amp adapter will work as a power source.
nope! that would ruin your stuff plus amps is what actually powers appliances so if you dont have enough it wont power up (amps is another word for current)
Probably yes. The 12v 2 amp adapter can put out 12x2=24 watts. The 60w adapter can handle more than twice the power (60 / 12 = 5 amps). However, the voltage of inexpensive adapters may be quite a bit higher under low loads. I'd check and make sure the voltage was not very much greater than 12 volts with a 2 amp load.
go by a little 12v adapter at radioshack for twenty or so dollars. that's what i do and it works and even powers a amp and 4 speakers
Yes, the larger cable can carry more load (current) than the other cable.
No, if your device require 3.0A, 1500ma adapter which is 1.5A is not enough, voltage wise is fine, your adapter adapter will get warm, then overheat, then very likely fail.
No, it is not recommended to substitute a 12 volt 0.5 amp AC adapter with a 7.5 volt 1 amp adapter. The voltage and amperage ratings need to match the requirements of the device you are powering. Using a lower voltage adapter may not provide enough power, and using a higher voltage adapter can potentially damage the device.
12 x 80 = 960 watts.
Your power adapter is rated up to 30 volts at 1000ma. (1 amp.) If you have a device which only draws 1 milliamp, then it should work with this adapter, as long as the voltage is correct.
no, it may damage the appliance.1Can_12V_2A_adapter_be_used_for_12V_1A_device, 2a adapter cannot be used for 12v, 1a device if the so mentioned parameters are input parameters of the device.Yes, a 12 volt 2 amp adapter has more that enough capacity to operate a 12 volt 1 amp device. In fact the adapter can operate devices up to a limit of 12 volts 2 amps. A device larger than 2 amps connected will tend to heat the adapter up and eventually cause it to fail.