bar x 14.503773773 = psi
1.5 bar x 14.503773773 = 21.76 psi (rounded)
150 MPa is equal to 21,750 PSI
Multiply psi by 0.006894759086775369 to convert from psi to MPa. ex: 1000 psi = 1000 x 0.006894759086775369 = 6.89 MPa http://www.chapelsteel.com/psi-mpai.html
about 2350 psi or 16.2 MPa
150 mm Hg is the same as 2.90 PSI: 1 atmosphere == 760 mm Hg, so 150 mm Hg is the same as 0.197 atm. 1 atmosphere = 14.696 PSI so (0.197)(14.696) = 2.90 PSI
You will need some other measurements to make it possible, since those are two different units of measurement. mph (or Miles Per Hour) is a measurement of speed, whereas psi (or Pounds Per square Inch) is a measurement of pressure. There is no direct conversion between them, however, if you know the volume of flow and the area it has to flow through, it should be possible to calculate. For example: A leaf blower rated at 450 cfm @ 250 mph when blowing through a 4 inch diameter pipe will produce "x" psi. So you need the flow rate and diameter to finish the conversion.
Titanium and its alloys have very high strength-to-weight ratios. The densities of titanium-based alloys range between 0.160 lb/in3 (4.43 gm/cm3) and 0.175 lb/in3 (4.85 gm/cm3). Yield strengths range from 25,000 psi (172 MPa) for commercially pure Grade 1 to greater than 200,000 psi (1380 MPa) for heat-treated beta alloys. Titanium and its alloys have very high strength-to-weight ratios. The densities of titanium-based alloys range between 0.160 lb/in3 (4.43 gm/cm3) and 0.175 lb/in3 (4.85 gm/cm3). Yield strengths range from 25,000 psi (172 MPa) for commercially pure Grade 1 to greater than 200,000 psi (1380 MPa) for heat-treated beta alloys.
Divide by 6.895 and multiply by 1000 to get psi (500/6.895) x 1000 = 72,516 psi
1 psi = 6.89476 kPa (rounded) 1 kPa = 0.14504 psi (rounded) 1 mPa = 1,000 kPa
1 psi = 64984.65 Pa Therefore 50 MPa = 769 Psi
1 MPa = 145.038 PSI.
The ultimate strength of annealed SS304 is 80,000 psi (550 MPa). Its yield strength is 30,000 psi, and its shears strength is 80000/(SQRT(3)) = 46000 psi. If it is cold worked, as for bolts, its yield and ultimate and shear strength will increase.
300 mpa
Multiply psi by 0.006894759086775369 to convert from psi to MPa. ex: 1000 psi = 1000 x 0.006894759086775369 = 6.89 MPa http://www.chapelsteel.com/psi-mpai.html
ASTM 1011 comes in many grades which determine the yield strength ie:1011 gr 42 would have a min yield of 42,000 psi
It is 217.556607 pounds per square inch.
MPa stands for Megapascal, a unit of pressure. 1 Mpa is equal to 145.0377 psi
MPa x 145 = psi
Commercial grade Titanium (92% pure) is 63,000 psi (434 MPa). Certain titanium alloys (e.g., Beta C) achieve tensile strengths of over 200,000 psi (1,400 MPa). Megapascal or MPa is a unit to measure tensile strength.