Want this question answered?
A higher wattage HPS bulb may work with a ballast that is rated for a lower wattage bulb , but may appear to be dim and will not produce the rated light output. It is best to match ballast and bulb accordingly.
No, it is not safe to exceed the recommended wattage on a fixture. The wattage rating indicates the maximum amount of power that the fixture is designed to handle safely. Exceeding this wattage can cause overheating, fire hazards, and damage to the fixture. Always follow the manufacturer's recommendations for bulb wattage.
Sure. Get a recessed light that is designed to be installed in "old Work". You must hav eenough room in ceiling to contain the recessed light. There may be some issues in some locations where the recessed fixture may overheat if for instance there is insulation around the fixture. Light should have an over temp cutoff. There should be a template with recessed light and a built in box to wire in the power from the old light. If you carefully cut out the sheetrock in ceiling according to the template dimensions, you will be able to use the piece you remove to repair the hole should there be no room for the recessed light. If there is attic access where the new light will be installed, you may be able to use a "new Work" light fixture since you can mount it from above. Go to someplace like Home Depot or Lowes and see what they have available.
Try moving the tube in the fittings, if this doesnt work, then you probably need a new starter motor.
By earth wire I am assuming you mean the bare wire and that a black and white wire are connected to the light. If when you connect the earth wire and breaker trips then there is a short between black and earth. It could be a bad ground connection, an internal short in the light fixture where black wire "hot" is connected to metal on the fixture through a nick in wire.
Some Recessed lights have a thermal cutoff. (Some flush mount ceiling lights too) Use a smaller wattage bulb.That is all that can be said without more info.
Some Recessed lights have a thermal cutoff. (Some flush mount ceiling lights too) Use a smaller wattage bulb.That is all that can be said without more info.
You can buy clips that attach to the spreader bars on the recessed light itself, then the clips attach to the suspended ceiling bars. You may need to add a pair of additional suspended ceiling bars to make this work. Armored cable should be run to energize the light.
A good type of office light which will light up your work are but not the space around you would be a desk lamp. Another good idea would be to put a low wattage fluorescent bulb in the lamp as it will provide a better light, at a much lower cost.
A higher wattage HPS bulb may work with a ballast that is rated for a lower wattage bulb , but may appear to be dim and will not produce the rated light output. It is best to match ballast and bulb accordingly.
Plasma ceiling mounts work by screwing into the ceiling. They have a mount which can hold a big-screen tv, so it will be suspended from the ceiling, as opposed on a stand or mounted on the wall.
No, it is not safe to exceed the recommended wattage on a fixture. The wattage rating indicates the maximum amount of power that the fixture is designed to handle safely. Exceeding this wattage can cause overheating, fire hazards, and damage to the fixture. Always follow the manufacturer's recommendations for bulb wattage.
Yes, both can work from the same set of switches.
By choosing ceiling fans with lights for your business or home, you can spread more light over your work area while also fanning people when the weather is warm. This increases productivity and comfort.
Sure. Get a recessed light that is designed to be installed in "old Work". You must hav eenough room in ceiling to contain the recessed light. There may be some issues in some locations where the recessed fixture may overheat if for instance there is insulation around the fixture. Light should have an over temp cutoff. There should be a template with recessed light and a built in box to wire in the power from the old light. If you carefully cut out the sheetrock in ceiling according to the template dimensions, you will be able to use the piece you remove to repair the hole should there be no room for the recessed light. If there is attic access where the new light will be installed, you may be able to use a "new Work" light fixture since you can mount it from above. Go to someplace like Home Depot or Lowes and see what they have available.
Paint the ceiling first. Work top down.
form_title= Fluorescent Light Bulbs form_header= Brighten up your home with fluorescent light bulbs! What wattage do you need?*= _ [50] How many bulbs do you need?*= {1, 2, 3, 4, 5, More than 5} Where will the bulbs be used?*= _ [50]