0
What else can I help you with?
Where is thermostat in 94 Honda Accord?
usually you follow the upper radiator hose to the engine you have to remove that hose and the thermostat is between the hose and engine block....sometimes you have to move the alternator to get there
What are the best garden hose storage devices?
The best garden hose storage devices are the barrel-shaped ones. They are easy to move. Removing the hose from the barrel is easier and it prevent tangling.
Where is the move forgeter in diamond?
he is in a hose in canalave city right in front of the pokemart.
How do you put of fire in malls?
Same as any fire except with longer lengths of hose and additional manpower to help evacuate people and move the hose.
If punctured which hose would empty a scuba tank at a faster rate high pressure hose or low pressure hose?
LOW PRESSURE HOSE: Yes, a low pressure hose. A high pressure hose has a very small diameter opening since it is just used to measure pressure and it is not performing any work. A low pressure hose is used to perform work and has a larger diameter opening so air can move through it.
How to change thermostat on 2000 Honda Civic?
First locate the lower radiator hose, that hose should lead you to the thermostat housing (just behind the motor and to the left). This hose should be the same size as the top radiator hose. Second you move the clamp (pliers will work) down the hose away from the thermostat housing, then loosen that hose from the thermostat housing. Third you take of the 2 Bolts off from the thermostat housing, they should be 10mm. Remove the thermostat. When you replace the thermostat you may also need to replace the gasket. Simply put the bolts back in and tighten them, then reattach the lower radiator hose and move the clamp back to its original position. Note: The top radiator hose does NOT lead you to the thermostat housing!
How do you test wastegate on caterpillar c-13 engine?
you apply 22 psi to the hose and it should move
What branch move to impeach?
Legislative branch. Hose impeaches, Senate tries the charges.
How can I replace a dryer vent hose?
To replace a dryer vent hose, first unplug the dryer and move it away from the wall. Remove the old hose by loosening the clamps at both ends and pulling it off. Measure the length needed for the new hose and cut it to size if necessary. Attach the new hose by sliding it onto the dryer and wall vent, securing it with clamps. Make sure the hose is properly connected and free of kinks to ensure proper ventilation.
How do you drain the power steering fluid in a 1989 Toyota pickup truck 4 cylinder?
Best way is to find the hose, usually the big hose that conects to the power steering resivour, and disconect the hose and it will drain out. Move the hose all the way down until no more fluid comes out. It will get messy depending on the location of the pump resivour.
How can I effectively clean my dryer vent hose using a dryer vent hose cleaner?
To effectively clean your dryer vent hose using a dryer vent hose cleaner, follow these steps: Disconnect the dryer from the power source. Remove the vent hose from the dryer and the wall. Attach the dryer vent hose cleaner to a vacuum or blower. Insert the cleaner into the vent hose and move it back and forth to remove lint and debris. Reattach the vent hose and plug in the dryer. Run the dryer on a no-heat cycle to ensure proper airflow. Regularly clean the vent hose to prevent future blockages and improve dryer efficiency.
How do you drain your above ground pool with a garden hose?
Siphon it out. You can create a siphon by either sucking really hard on one end of the garden hose while the other end is under water, or the easier way, with 2 garden hoses as follows: -Get 2 garden hoses. Hook one to the spigot, put it in the pool and turn it on. set the other hose up with one end in the pool, and the other wherever you want to drain the water to. -Hold the ends of the 2 hoses that are in the pool, together with your hands, so the spigot water runs through the 2nd hose. Pull them apart, and you will feel the suction pulling the water out of your pool through the empty hose. -Take the hose that is connected to the spigot, out of your pool, and turn the spigot off. -Make sure the other garden hose does not fall out of the pool, or you will lose suction and have to start all over again! -When you get towards the bottom, you will have to physically hold the hose and move it around to get the water out without losing suction. You have to have the end of the hose that the water is running out of below the level of the bottom of the pool. You can do it with on.y one hose. Put one end of the hose in the pool and connect the other end to the faucet and turn it on until the air is forced from the hose. If the faucet is below the pool just disconnect the hose and lay it on the ground. You can move it around as long as the end of the hos estays below the top of the water. If the faucet is above the water level have someone put thier finger over the end of the hose in the pool while you move the end of the hose to a spot below the bottomof the pool.
