0
How does blasting air into a blast furnace raise the temperatrure?
Sugarx
Occuring chemical reactions (coke combustion) are exothermic.
Wiki User
∙ 6y ago
Add your answer:
Earn +20 pts
How do you raise your power level in raging blast?
ofcoures charge up
How do you raise kia up in dragon ball z raging blast?
down directional button
How is iron ore converted into iron?
you can smelt it. You put it in a blast furnace with carbon. This will be able to separate the iron from the iron ore The carbon is in the form of coke, providing both fuel for the huge amount of heat at the high temperature needed, and the carbon necessary to separate chemically the iron from the iron-oxide which is the ore itself. Limestone is added as a flux to help remove silica and other impurities as molten "slag" that floats on the molten iron, and is tapped off separately. The "blast" part refers to the powerful blasts of air pre-heated by the furnace's flue gases, and blown into the fire to raise it to white heat.
Where is the furnace located to light pilot light?
It could be different for every house.A side note: I'm taking that you mean where is the pilot light located in side your furnace? Depending on the of your furnace it's very possible your furnace does not have a pilot light, in fact it may have an ignition system with a flame management sensor. Try this; turn off the system with the main electrical cutoff switch, wait for about 2 minuets, turn on the switch raise the temperature of the thermostat high enough for the furnace to come on, this should work if it does not try one more time. If that fails call a HVAC & R technician.
What is a slot raise?
A slot raise is used in mining for shaft sinking and/or raising (drilling tunnels upwards at 45 to 90 degrees off horizontal). When rock is blasted it expands to about 300% of it's original volume so when drilling a tunnel you need a void to give the blasted rock somewhere to expand into. Rather than drill a large diameter tunnel upwards in one go (running the risk of the expanded rock compacting in place and "freezing" the tunnel) it is common to blast out a small diameter tunnel first - a "slot raise" - and then come back and drill and blast the larger diameter tunnel using the slot raise as a void to allow the blasted rock to expand.
Difference between walking beam and walking hearth furnace?
A walking beam furnace allows the product to be heated from all sides, where a walking hearth furnace only alloys product to be heated from the top and is more suitable for thinner products. There is no major mechanism difference between a walking hearth and a walking beam furnace. For a walking beam furnace, an actual walking beam will lift the product and move it forward. Then the product is lowered onto the stationary beams. While the load is resting on the stationary beams the walking beam moves underneath the product back to the home position ready to perform another walk. Whereas for a walking hearth furnace, portions of the refractory lined hearth are used to raise the product and move it toward the discharge in a walking fashion. Both mechanisms of moving the product to the discharge, are almost identical.
How does lean muscle mass raise metabolic rate?
Increasing the amount of muscle you have will raise your metabolic rate. For example, if you add ten pounds of muscle in the next year through proper strength training your body will consume an additional 350 to 500 calories daily. Muscle is your metabolic furnace that burns additional calories 24 hours a day (not just during and immediately after exercise).
What is the future tense of raise?
The future tense of "raise" is "will raise" or "shall raise."
What is the future tense for the verb raise?
Will raise is the future tense of raise.
How to Clean an Oil Furnace Heat Exchanger?
If you have a heat exchanger within your oil furnace, you probably know that it is of vital importance that you must regularly clean out the buildup of soot inside of it. You should probably do this at least once every passing year. If you let too much soot sit in the furnace, it will probably raise the power bill significantly, it will significantly raise the risk of fire and it will also end up forcing carbon monoxide to enter the home, which has a reputation for being deadly. You should let a technician assist you in flame adjustments, much the majority of people and homeowners can easily clean out the soot that builds up within the heat exchanger.For this project, you are going to need the manual which came with your oil furnace, a small brush that has stiff feeling bristles, a flashlight, a soft cloth, a wet and dry vacuum cleaner, a dust mask and some safety glasses.Look for the panel that can be opened on your oil furnace. If your furnace is designed to be lowboy, you will probably have the door in the very front of the design. The side will have the panel for cleanup if you have a horizontally designed furnace. You should consult with your manual to find the location that you are looking for, since it does cater to the specific model that you are cleaning.Take the small brush with stiff bristle and brush away at the soot so that it can loosen up and be made much easier to clean it up. The heat exchanger is located directly inside of the furnace unit. You may experience some difficulty in reaching the heat exchanger, but this is why you will have the flashlight for assisting you in locating this dark and hidden location.Take your vacuum cleaner and vacuum up the soot that has built up. You may need to alternate between brushing off some of the debris of soot that has built up and using the vacuum to suck it up. Once you have completed this task, though, you can use the dampened washcloth to wipe it down and get the remaining debris and cleanse it before you close the door again.
How does a anaconda raise its young?
They do not raise them.
Where do they raise animals?
They raise them on farms
