0
Add your answer:
Earn +20 pts
Where can one purchase a current probe?
One can purchase a current probe from the tek website. One can also purchase the current probe from Amazon. One can use the current probe to measure circuit.
How do you use the word probe in a sentence?
One day i would like to probe the bottom of the ocean!
How do you check the stop light switch for power on one side of a 2004 jeep Cherokee?
use a test light with the alligator clamp attached to a ground and use the probe to test each side of the switch for power
Does a space probe use fuel?
sometimes yes, but more often it runs on solar power
What is use of logic probe in electronic?
we use logic probe in circuit because logic probe is use to indicate where signal is high or low on ic chip.
How do you use a wiggler?
The wiggler body holds the selected probe. Loosen the knurled nut and snap the ball on the end of the probe into the body. Tighten the knurled nut so the probe is not loose, but can still move. When using the dial indicator probe, tighten it firmly. Put the shank of the body into the chuck, end mill holder or collet on your mill or drill press. Use the point probe to find a point on a work piece. This is the probe you use to locate scribed lines on a work piece under the drill or mill chuck. Center the probe by turning on the machine to about 1000 RPM. Use a wooden pencil or other object to press on the side of the probe near the point until it turns true, with no wobble. When you press too hard you will find out why this device is called a wiggler! Once you have the probe centered, turn off the power and center the mark on the work piece under the point of the probe. Use the disk probe to find the edge of a work piece. The disk on the end of this probe is 0.100” in diameter. Center the probe by turning on the machine to about 1000 RPM. Use a wooden pencil or other object to press on the side of the probe near the point until it turns true, with no wobble. Leave the power on as you move the side of the work piece into the tip of the probe. When the probe touches the side of the work piece it will start to wobble. The center of the spindle is 0.050” from the edge of the work. Use the ball probe to find the center of existing holes. Center the probe by turning on the machine to about 1000 RPM. Use a wooden pencil or other object to press on the side of the probe near the point until it turns true, with no wobble. Once you have the probe centered, turn off the power and center the existing hole in the work piece under the ball of the probe. This probe can also be used to find the edge of a work piece. The smaller ball on this probe is 0.250” in diameter, so when it touches the side of the work piece, the center of the spindle is 0.125” from the edge of the work. Use the indicator probe to mount a dial test indicator. Use a dovetail clamp or a body clamp to attach the dial test indicator to the indicator probe. You can use this to check the alignment of a vise on your mill.
How do you fix Audi A4 brake and reverse lights the bulbs are okay also checked the fuse but still they wont work What should I do?
If you have access to a power probe, use a power probe and see if your getting power to at lease going through the wires. Maybe your actually plugs are messed up.
What is the difference between a satellite and a probe with regard to orbital velocity and escape velocity?
Well, a satellite revolves about 80 times faster than the probe. The probe masters different situations which cause orbital problems. Escape velocity doesn't have the power that regards to the probe. Scientists assume that the satellite has the power, but others don't. The probe connects to orbital velocity and has the power to control it.
How do you find the hot wire for the CD player on a 1988 Chevy Celebrity?
With the radio wire harness where you can get to use a light probe to find a wire with power to it, ignition key off. That will be the always hot wire that is used to power the memory that remembers stations when the radio is off, it should be yellow. Make note of which wire that is. Then with the key on probe the connector again for a second hot wire, it should be red. That will be the one I would think you would want to use to power your CD player
What is use of probe?
inday
How do you use probe in present tense?
I/you/we/they probe. He/she/it probes. The present participle is probing.
Is ther a negative and a positive probe in a voltmeter?
Yes, the black probe is the negative one (kathode) and the red probe is the positive one (anode)
