0
What else can I help you with?
How do you install a supercharger on a Ford probe?
Can a supercharger work on a 97 ford probe
Will an ultrasound probe still work?
The functionality of an ultrasound probe depends on various factors such as the condition of the probe, how well it has been maintained, and the specific issue it may have encountered. In general, if an ultrasound probe is well-maintained and not physically damaged, it should continue to work effectively.
How do you use a wiggler?
The wiggler body holds the selected probe. Loosen the knurled nut and snap the ball on the end of the probe into the body. Tighten the knurled nut so the probe is not loose, but can still move. When using the dial indicator probe, tighten it firmly. Put the shank of the body into the chuck, end mill holder or collet on your mill or drill press. Use the point probe to find a point on a work piece. This is the probe you use to locate scribed lines on a work piece under the drill or mill chuck. Center the probe by turning on the machine to about 1000 RPM. Use a wooden pencil or other object to press on the side of the probe near the point until it turns true, with no wobble. When you press too hard you will find out why this device is called a wiggler! Once you have the probe centered, turn off the power and center the mark on the work piece under the point of the probe. Use the disk probe to find the edge of a work piece. The disk on the end of this probe is 0.100” in diameter. Center the probe by turning on the machine to about 1000 RPM. Use a wooden pencil or other object to press on the side of the probe near the point until it turns true, with no wobble. Leave the power on as you move the side of the work piece into the tip of the probe. When the probe touches the side of the work piece it will start to wobble. The center of the spindle is 0.050” from the edge of the work. Use the ball probe to find the center of existing holes. Center the probe by turning on the machine to about 1000 RPM. Use a wooden pencil or other object to press on the side of the probe near the point until it turns true, with no wobble. Once you have the probe centered, turn off the power and center the existing hole in the work piece under the ball of the probe. This probe can also be used to find the edge of a work piece. The smaller ball on this probe is 0.250” in diameter, so when it touches the side of the work piece, the center of the spindle is 0.125” from the edge of the work. Use the indicator probe to mount a dial test indicator. Use a dovetail clamp or a body clamp to attach the dial test indicator to the indicator probe. You can use this to check the alignment of a vise on your mill.
Will a 1989 ford probe transmission out of the 4cly fit the 1990 probe v6 both being a 5 speed?
i think that it might work
Is a 1996 Ford Probe 5 Speed transmission interchangeable with a 1991 Ford probe 5 Speed?
no but if you can find an 88 to 92 tranny it will work fine
What could be wrong if your air conditioning does not work on a Ford Probe?
Mine is out of Freon.
Will fuel pump from Ford Mustang work in ford probe gt?
Absolutely not.
How do meat thermometers work to accurately measure the temperature of food?
Meat thermometers work by using a metal probe to measure the internal temperature of the food. This probe sends a signal to a display unit that shows the temperature. The accuracy of the measurement is based on the probe's ability to detect heat and the display unit's ability to show the temperature.
What is the probe size?
Probe,probe se 2.0 / probe gt 2.5
Why does your heater only work when car is moving 97 ford probe?
low on coolent
Can a 1994 2.0 Ford Probe engine work in a 1996 Mazda 626 2.0?
NO!
What can you match Ford Probe fuel pump with?
No need to match it to any other pump. Just purchase a fuel pump for your Ford Probe and it will fit and work. You for sure do not want to install a used fuel pump. Way to much work to change it out.
