How does the ford flex awd work?

Answer 1

Torque from the engine is transferred through the transaxle to the PTU. This torque is transferred from the driveshaft to the rear axle, which drives the rear halfshafts. The AWD system, referred to as an Active Torque Coupling (ATC) system, is always active and requires no driver input.

The AWD system continuously monitors vehicle conditions and automatically adjusts the torque distribution between the front and rear wheels. During normal operation, most of the torque is delivered to the front wheels. If wheel slip between the front and rear wheels is detected, or if the vehicle is under heavy acceleration, the AWD system increases torque to the rear wheels to prevent or control wheel slip.

Serviceable components of the PTU are limited to the output shaft seal and flange, intermediate shaft seal and deflector, and the PTU transaxle compression seal. No internal components are serviced. There should be no need to remove the PTU cover. If any of the internal geared components, bearings, case cover or shafts are worn or damaged, a new PTU must be installed.

The vehicle is equipped with an All-Wheel Drive (AWD) system, also referred to as Active Torque Coupling (ATC), that is always active and requires no driver input. The system has no Mode Select Switch (MSS).

The system continuously monitors vehicle conditions and automatically adjusts the torque distribution between the front and rear wheels. During normal operation, most of the torque is sent to the front wheels. If wheel slip between the front and rear wheels is detected or if the vehicle is under heavy acceleration (high throttle position), the AWD system increases torque to the rear wheels to prevent or control wheel slip.

If the spare tire is installed, the AWD system may disable automatically and enter Front Wheel Drive (FWD) only mode to protect driveline components. This condition may be indicated by an AWD OFF message in the message center.

If there is an AWD OFF message in the message center from using the spare tire, this indicator should turn off after reinstalling the repaired or replaced normal road tire and driving a short distance. It is recommended to reinstall the repaired or replaced road tire as soon as possible. Major dissimilar tire sizes between the front and rear axles could cause the AWD system to stop functioning and default to FWD or damage the AWD system.

AWD faults may be indicated by the wrench lamp in the Instrument Cluster (IC) as well as CHECK AWD message in the message center.

The system consists of a Power Transfer Unit (PTU), 4X4 control module, rear axle and a solenoid actuated ATC device. Based on the amount of current sent to the clutch, the module varies the torque sent to the rear wheels by sending a duty cycle to the ATC device, located inside the rear axle.

The 4X4 control module also provides the brake system with its current clutch duty cycle and determines whether or not the brake system may take command of the clutch duty cycle.

NOTE: The ATC solenoid is not repairable. If a new component is required, the ATC solenoid and rear axle are installed as an assembly.

The active, on-demand AWD system uses data from other systems as inputs to the 4X4 control module. The 4X4 control module uses the inputs to determine the appropriate amount of current to send to the ATC solenoid that delivers the desired torque to the rear wheels.

Specific inputs to the 4X4 control module are:

Accelerator pedal position via the High Speed Controller Area Network (HS-CAN)

Transaxle range from the PCM via the HS-CAN

Brake system status from the ABS module via the HS-CAN

Wheel speed from all 4 wheels from the ABS module via the HS-CAN

4X4 control module outputs are:

Solid-state clutch (pulse-width modulated signal) to the ATC solenoid

Percent of torque transfer commanded signal to the ABS module via the HS-CAN

Torque request available signal to the ABS module via the HS-CAN

Heat Protection Mode

During very extreme off-road operation, the All-Wheel Drive (AWD) system utilizes a heat protection mode to protect the Active Torque Coupling (ATC) solenoid (part of rear axle) from damage. If the system detects an overheat condition, it enters a locked mode. If the heat in the system continues to rise once in the locked mode, the 4X4 control module disables the ATC solenoid. This condition may be indicated by an AWD OFF message in the message center. Allow the system to cool down at least 10 minutes with the ignition switch in the ON position.