0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What does a circuit breaker look like for 110 volt?
Most of the breakers in a panel will be 120 VAC. Double height breakers are 240 VAC. A triple height breaker probably indicates you have 3-phase power in the panel.
My seimans elect panel box let me put in tandem breakers?
I wnt to install a tandem breaker but my panel box won't let me. Why?
What circuit breaker to install for 10 amp 250 volt circuit?
You need a breaker rated for 10 amps and 250 volts. The breaker must also fit properly in your panel.
How do you wire a 15 amp 120V breaker in a 240v 30 amp breaker panel?
Look to see if the 30 amp panel is fed with a two wire or a three wire. If it is a two wire then you are out of luck. If the panel is fed with a three wire then the panel should have the neutral terminated in the panel. It is this neutral that you need for 120 volt connections. You didn't state how many panel slots there are in the panel. If you are able install a 15 amp breaker into the panel and connect the wires going to the load. The black wire will go to the breaker and the white wire will go to the neutral bar in the panel.
Can a Siemens breaker push on be a replacement breaker for a Westinghouse breaker?
only if listed in the panel board
What is the proper height of a breaker panel?
5'6"
What do I do if there is no circuit breaker for outdoor light?
If you have a light that is not being powered through a circuit breaker or fuse, you should call a qualified electrician to remove this circuit from the panel's bus and install a circuit breaker for it. Without an overcurrent protective device (circuit breaker or fuse) you have a potential fire hazard.
What is a sentence with the words circuit breaker in it?
Example sentence - We hired an electrician to at the circuit breaker and install an updated panel.
What does a circuit breaker look like for 110 volt?
Most of the breakers in a panel will be 120 VAC. Double height breakers are 240 VAC. A triple height breaker probably indicates you have 3-phase power in the panel.
My seimans elect panel box let me put in tandem breakers?
I wnt to install a tandem breaker but my panel box won't let me. Why?
What circuit breaker to install for 10 amp 250 volt circuit?
You need a breaker rated for 10 amps and 250 volts. The breaker must also fit properly in your panel.
Where is the proper location for a main breaker in a panel?
Normally the main is on the top but you can install a service panel with the main on the bottom unless local codes prohibit it.
How do you wire a 15 amp 120V breaker in a 240v 30 amp breaker panel?
Look to see if the 30 amp panel is fed with a two wire or a three wire. If it is a two wire then you are out of luck. If the panel is fed with a three wire then the panel should have the neutral terminated in the panel. It is this neutral that you need for 120 volt connections. You didn't state how many panel slots there are in the panel. If you are able install a 15 amp breaker into the panel and connect the wires going to the load. The black wire will go to the breaker and the white wire will go to the neutral bar in the panel.
What type panel does a 4 pole breaker require?
The panel and breaker have to be of the same manufacturer. This way the breaker will fit into the panel. If the panel has a push in bus bar, the breaker must also be the type to accept the bus bar. If the bus bars in the panel are of the bolt in type then the breaker also has to be a bolt in breaker.
How do you connect 200amp from main panel to sub panel to the lug of the min panel to lug of sub panel?
Not exactly sure what your question is and you need to make sure you are in compliance with electrical code for your jurisdiction. But, generally speaking you install a large breaker (let's say 100A 2 pole breaker to power the sub panel) just as you would install any other breaker in the presently used (hot) panel, and the proper sized cable then goes from old to new and terminates on the main lugs of the new panel. Ground and neutral are usually isolated from each other in the sub panel but depends on other factors as to location of the sub panel, etc.
Is it okay to install a Square D breaker in a GE panel?
It probably wont fit. But if it does there should be no other reason why it wouldn't work.
How would you install ge circuit breakers?
There are many ways one can install ge circuit breakers. One can install ge circuit breakers by turning off the power supply, removing the panel cover, testing it for power, and installing it by alining the breaker with the unused panel space.
