0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How does the drip tip plant adapt to it's environment?
it is thick and waxy with a special tip at the end so when it rains the water fall right off the tip. therefore the name drip tip
How far is it from north to south japan?
Japan is a crescent-shaped island. It is 1,869-miles from the northeast tip to the southwest tip. It is 1,022-miles from the northwest tip to the southeast tip.
What is a leaf tip?
a leaf tip means above the side of a leaf
How many kilowatt hours does a fifty gallon electric hot water heater use per month?
This is hard to give an exact quantity due to the variable habits of people's hot water use. Some people take a 10 minute shower others 2 minutes. Amount of people using the hot water tank in the family. To make an accurate assessment there would need to be a hour meter installed on the tank over the month's use and to calculate the final answer the wattage size of the elements would be needed.
What are the different types of urinary catheters?
There are several types of catheters: Whistle tip, Olive tip, Round tip, Flexible filiform tip, Blasicci curved, Braasch bulb, Acorn, Foley, Pezzar, etc.
How do you temper a chisel at home?
Heat the tip with a propane or MAP gas torch until it is red hot. Quench it in cold water.
What type of tip do you use to braze?
Brazing can be done with a small torch or a big soldering iron. Either electric or brazier heated. The tip on a torch should be small as you don't need the heat you use when gas welding or cutting.
What is the name of a welding torch tip that has two ends?
Mig tip
What is the total height from ground to the tip of the torch?
The statue is about 305 feet tall from the bottom of the pedestal to the torch.
What is the elevation above sea level of the tip of the torch of the statue of liberty?
The tip of the torch of the Statue of Liberty is approximately 315 feet above sea level.
What is the difference between electrical and torch soldering?
When soldering a person can use an electric tool or a torch. The torch uses a flame, while an electrical tool has a soldering tip which is heated.
What is the height of the statue of liberty from the base to the torch in inches?
Vital statistics: Top of base to torch 151'-1"Ground to tip of torch 305'-1"More info by accessing related link below:
What torch do you use in welding to produce a variety of flame sizes?
A welding torch as opposed to a cutting torch is more appropriate . Welding torches accommodate a variety of tip sizes designated by a number and have only one orifice (hole) for the flame. The smaller the number the smaller the tip orifice (hole) and a smaller flame. Larger numbers means larger hole sizes and larger flames. Sizes start at 0 and can be as large as 40 or more. The size of the tip is determined by the thickness of material to be welded/brazed. Thin materials would call for a small tip size, thick materials would need a larger tip size.
What is the proper way to cut iron with a torch?
What are you calling Iron. steel is the only material that can redilly be cut with a cutting torch.Aside from that having the rite tip & adjusting the torch properly are essetial,one can use propane or map gas or acetelyne along with oxygen.Most often refered to as oxy acetylne torch. Assuming you have the correct equipment tell me what material & how thick ,I may be able to direct you from there. I have 35 yrs of exprience in the industry Grampa knows!
How do you get support bearing off the driveshaft on 77 chv PU?
If you are very careful you can use a cutting torch with a small tip.
Explain oxy- acetylene welding process?
Oxygen and acetylene tanks feed into your torch. When opened, the gases will mix in a chamber in the torch, then flow out of the torch tip. Using a spark lighter, they will ignite causing a flame. This flame can be adjusted to a neutral flame by moving the knobs on the tank regulators.
What tip of meat is a hot dog?
lips and beaks
