Want this question answered?
explosion of an atom bomb releases large amount of energy as heat liberation resulting rise in temperature and deformation in matter and pressure and many more forms of energy obtained from matter.
PV = NkT P: pressure V: volume N: number of particles in gas k: Boltzmann's constant T: absolute temperature More particles in a constant volume, constant temperature space means more pressure.
Charles' Law says that as pressure on a gas decreases, its volume increases. Charles' Law is an example of an inverse relationship.t It is not Charle's law It is Boyle's law Charles law states at constant volume, pressure is proportional to kelvin temperature And at constant pressure volume is proportional to kelvin temperature But Boyle's law states that at constant temperature pressure is inversely related to volume
For a given mass at constant temperature, the pressure time tghe volume is a constant. pV=C
If you are talking about a temperature and pressure valve on a water heater (pop off valve). It is controlled by spring pressure and a rubber seal. As pressure in the tank increases the tension exerted by the spring on the rubber seal is over come until the point at which excess pressure is released around the rubber seal. When the pressure inside the tank decreases the spring again pushes the rubber seal closed. Temperature of the water in the tank is directly related to the pressure.. higher temperature = more pressure.
as pressure increases, temperature increases
Temperature is related to air pressure because the air pressure can determine the movement of wind. If cool winds move from areas of high pressure to low pressure zones, the temperature in that place will drop.
Temperature is not directly tied to volume, its related to pressure. Increasing the temperature will increase the pressure--only if volume is held constant. That is were volume and temperature are related, through pressure. However, if you increase the volume it does not change the temperature.
Temperature is not directly tied to volume, its related to pressure. Increasing the temperature will increase the pressure--only if volume is held constant. That is were volume and temperature are related, through pressure. However, if you increase the volume it does not change the temperature.
explosion of an atom bomb releases large amount of energy as heat liberation resulting rise in temperature and deformation in matter and pressure and many more forms of energy obtained from matter.
Deformation can create metamorphic rock structures.....
By Deformation.
Screw Science.
In the molding process of transforming plastic particles into plastic products, plastic is often subjected to high temperatures and pressure and flows under a high shear rate. Different molding conditions and processes will have different effects on the quality of products, and injection molding has four components: plastic raw materials, injection molding machine, injection mold, and plastic injection molding process. If the plastic raw materials are correctly selected, the technical process parameters of the injection molding machine and mold structure are in line with the requirements of injection molding conditions, so the quality of processed products is directly related to the injection molding process. The quality of the product has the internal material quality and appearance quality, the internal material quality is mainly mechanical strength, and the size of the internal stress directly affects the mechanical strength of the product, the main reason for the internal stress is the crystallinity of the product and the orientation of the molecules in plastic molding, etc. The appearance quality of the products is the surface quality of the products, but the warpage and deformation caused by the internal stress will also affect the appearance quality problems. The appearance quality of products includes product shortage, product dent, fusion mark, flying edge, bubble, silver wire, black spot, deformation, crack, delamination and discoloration, etc., all related to injection molding temperature, pressure, flow time, and position. Molding temperature Barrel temperature, plasticizing temperature, nozzle temperature, mold temperature, and plastic drying temperature, etc. Barrel temperature: it is the melt temperature of the plastic. If the barrel temperature is set too high, the viscosity of plastic will be low after melting, and the injection speed will be fast under the same injection pressure and flow rate, and the molded products will be easy to fly, silver, discolored, and brittle. If the barrel temperature is too low, the plastic will be poorly plasticized, the viscosity will be high, the injection speed will be slow under the same injection pressure and flow rate, and the molded products will be easily deficient, with obvious melt marks, unstable size and cold lumps in the products. Nozzle temperature: high nozzle temperature setting, nozzle salivation, resulting in products with cold material wire. Low nozzle temperature causes clogging in the mold casting system. Injection pressure has to be increased to inject plastic, but there are cold material lumps in the instantly molded products. Mold temperature: high mold temperature, injection pressure, and flow rate can be set lower, but under the same pressure and flow rate, the products are easy to fly, warp and deform, and the products are difficult to stick to the mold and eject. Mold temperature is low, in the same injection pressure and flow rate, the products are not enough, bubbles, fusion marks, etc. Plastic drying temperature: various plastics have different drying temperatures. ABS plastic is generally set a drying temperature of 80 ~ 90 ℃, otherwise, it is not easy to dry and evaporate the water and residual solvent, the product is easy to have silver and bubbles, and the strength of the product will also be reduced.
By marriage. Humidity and temperature are related. The maximum absolute humidity increases with temperature and pressure (up to the boiling point).
Under controlled situations , as the temperature increases the air pressure decreases.:)
Wind is related to air temperature because they both are dealing with high and low pressure. hopefully i help u out sincerely, Swagglikeme