0
The timer is used to set the intervals at which the light is exposed to the photographic paper. After the timer is turned on, there is a switch that sets the exposure time. This can be put into milliseconds, seconds, or minutes. Often the photographic paper is exposed for around 15 seconds, though this depends largely on the quality of the negative, style of the photographer, contrast of the print, etc.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Which forms of settlement develops along either side of roadsrivers or canals?
linear
Which type of moraine forms along each side of a glacier?
A medial moraine.
What did bando make out of clay in your side of the mountain?
Bando Made pottery with the clay they found along the stream bank. The Pottery was for the Jam they made in "MY SIDE OF THE MOUNTAIN"
What is the function of Radial artery?
major artery that carries blood to the lower arm along the side by the thumb.
Where is the heater Motor located on a Buick Regal?
should be on the passenger side right along the fire wall
How to Learn Photography and Darkrooms?
To begin with, it is elemental that a darkroom must be dark, with the use of a red safe light. Every door or window must be sealed against outside light. Sometimes a short hallway type of entrance prevents light from interfering when anyone enters the darkroom. Black masking tape or a blackout shade can be used on any windows. To make sure that the door is sealed against light, then a blackout shade that extends beyond the actual door edges needs to be secured.Every darkroom must have a wet side and a dry side. The dry side is where the enlarger is located. Preferably, the enlarger should be mounted on a counter long enough to provide clear working space on both sides. Film tanks, reels, a timer, easels for different size prints, a paper cutter, a drawer to store photographic papers, and a place to hang film and prints to dry are all essential to a well functioning darkroom. The type of enlarger to install is based upon what types of photographs are planned to be processed. Whether black and white or color, and the size of the enlargements desired are factors that enter into the choice of enlargers. Easels are available in various sizes, for handling 5 x 7, 8 x 10, or 11 x 14 inch prints. Naturally, if large prints are to be done, then the drawer for storing papers must be large enough to handle them.The wet side includes a sink or two, trays to hold developing fluids and water, hoses to allow for water to be channeled to such trays and sinks, tongs to use for lifting negatives and prints from trays and other containers, film clips, dark bottles for chemical storage, and supplies for cleaning work areas. Moving prints from developer to fixer to water trays requires that they be situated in a way that allows for a smooth uninterrupted movement. The placement of drying lines to clip finished prints on must be located in a place where there will be no dripping on either the photographer or on to things on counters. Planning out the darkroom beforehand will reveal any such bad placement of drying lines and equipment.
How do you wire an outdoor timer into a GFCI outlet?
I assume you are hard wiring it and not plugging it in. The power coming into the GFCI outlet connects to the line side of the GFCI outlet. If you want the outdoor timer protected by the GFCI then connect the wire going to the timer to the load side of the outlet. If you do not want the timer protected then connect it to the line side. On the back of the GFCI if you look closely you will see Line & Load marked on the back.
What would happened if you wired a 240v ballast and a 120 v ballast into a heavy duty timer?
The timer has to be multi-pole. The ballast must be connected to the load contacts of the timer. If the timer is a 120 Volt timer, the timer has to run on a 120V. circuit. Loads are loads, and as long as you have a multi-load timer you can hook up whatever you want. If the timer only works on a shared power source (load shares the timer supply) you will need to use a contactor on the load side or the timer.
Where in the x-ray circuit is the timer located?
On the primary side of the high voltage transformer.
Where can i find an online 10 second timer?
I do not think that u can find a useful 10 second online timer. I am not sure what you would like to time, but just the request to a server will porbably take more than 10 seconds. You can maybe use a client side timer, that is, one that runs a program on your own computer, just a java script timer that runs on you web browser . That may be ok, but directly to look at a server side timer, software that runs on a remote web site, is not a good solution. Hard to say what you need the timer for. There are some java script links below that may be helpful. If you give more details about the application of the timer, maybe i can help you
How do you get 13 minutes from a 7 minute and a 5 minute eggtimer?
you flip both timers (with all of the sand on one side) and once the five minute timer runs out the first time, you flip the five minute timer. Once the nine minute timer runs out, you flip the five minute timer again. After the five minute timer has run out, it will have been 13 minutes. (5+4+4=13)
How do you wire a timer switch to a 3 way light switch?
First you need to decide what you are trying to accomplish. You can wire the Timer switch in series with or parallel to the 3-way switches. If in series then the 3-way switch function would depend on the timer state. If the Timer switch was ON then the 3-way switch could turn the connected device ON or OFF from either location. If the Timer switch were OFF the device would be OFF no matter what you did with 3-way switches. To wire in this fashion put the timer between the supply and the input to the switches. If the Timer is in parallel then if the Timer is ON it doesn't matter what you do with the 3-way switch, the device will be ON as long as the Timer is ON. If the Timer is OFF then the 3-way switches will work in their normal fashion. To wire in parallel connect the supply to one side of the Timer and the device to the other.
Where is the central timer module on a 2002 dodge ram 4x4 truck?
under driver side dash
What is the radiator fan timer unit on a 1993 Acura Legend?
On the passenger side-Under the ECU cover.. On he
Where is the central timer module on a 2002 dodge Dakota quad cab?
On the driver's side, behind the kick panel to the left of where the driver's left ankle might be when sitting in the vehicle. Along side the emergency break pedal. Easy to access. Check out this web site for assistance: http://autorepair.about.com/library/a/1i/bl736i.htm
How do you operate montgomery ward sauna model 74-93025?
Set the timer then the heat
Where is the rear defrost timer located in a 1987 ford crown Victoria?
on the back side of the heater control panel
