0
What else can I help you with?
How do you remove old cement fence posts?
To remove old cement fence posts, start by digging around the base of the post to expose the concrete. Use a sledgehammer or a pry bar to break up the cement, loosening it from the soil. If the post is particularly stubborn, you can try pouring water around the base to soften the ground. Once the concrete is broken up, pull the post out of the ground, using leverage if necessary.
How do you pull up a hardwood floor that has been glue to the cement base?
With crowbars and long scrapers. -and it's a back-breaking job -- good luck !
How can I effectively pull moisture out of cement?
To effectively remove moisture from cement, you can use a dehumidifier or apply a desiccant like silica gel. These methods help to absorb excess moisture and speed up the drying process of the cement.
What is rubber cement thinner?
first of rubber cement is a type of glue you can buy almost any where and well rubber cement thinner is like glue remover it makes it so you can pull apart what you glued and its good clean up for a mess you make with it.
How do you fix a flooded toilet?
Take a GOOD plunger, place it firmly at the bottom af the bowl and vigorously plunge multiple times (as if you have been at it for some time and are aggravated) and on your last pull, pull hard. The first half a dozen quick plunges loosen the obstruction and the last hard suction pull breaks it free. Repeat if needed. You may consider pouring down a gallon of bleach and let set overnight. (Do Not Flush after pouring bleach)
What type of volcano forms where plates pull apart?
A shield volcano forms where plates pull apart. This type of volcano has gentle sloping sides and is characterized by its low viscosity lava flows. Examples of shield volcanoes include those in Hawaii.
How do you you pump a balanced cement plug?
Balanced cement plug is pumped through drill string or open-ended tubing. 'Balanced Cement Plug' means that the top of cement outside the drillstring/ tubing will be the same height as the top of cement inside the drillstring at the end of pumping. The drillstring/ tubing is then slowly pulled from the wet cement, allowing the cement inside the string to fill the centre of the plug. There are lots of refinements in this method with open hole cement retainers or high viscosity 'cushions' often placed below cement. In vertical hole, most balanced plugs are successful. In extended reach wells, failure rates can be high with cement slumping and mixing with synthetic based muds. A typical checklist to improve cement plug success in extended reach wells would have: 1. Always use a tailpipe. This reduces the disruption to the plug caused by removal of the drillstring. 2. Clean up the hole thoroughly before pumping cement. Cement is an excellent hole cleaner. Many 'flash set' events reported are really packoffs caused by cement picking up a cuttings dune. 3. Put a diverter tool with BIG holes on the bottom of the tailpipe. This directs fluids up the hole during cementing 4. Use a scavenger spacer in front of the cement job to convert the formation from oil wet to water wet. 5. Slow down pumping to 1 BPM while displacing cement into open hole. This reduces mixing of cement and mud. 6. Put a cushion below the cement plug. A cement retainer is best. If a viscous cushion is spotted, weight the cushion to 1 ppg below the cement weight. 7. Gravity is NOT on your side. Cement can stay inside the tail pipe as you pull it from the plug. Pump the volume of cement inside the tailpipe as you pull the tailpipe from the plug. 8. Circulate clean the long way with the bottom of the tailpipe at the planned cement plug top.
Have Justin bieber pull a prank on a fan?
Yes he has. Okay so once, I saw this video on youtube where he was pouring water on them and shooting water at them ( From his water gun )And yeah.Have Fun.Kassie
Where does a riftvalley form at?
It forms at a plate boundary. It deepens as the plates pull apart.
When two pieces of continental crust pull apart a what forms?
a valley or a canyon
How does a rift form?
A rift valley forms when the lithospheric stretches, tension stress occurs, causing rock to pull apart, break, and form normal faults.s the hanging wall of a normal fault slide down the footwall, a long, flat, narrow rift valley forms.
What type of landform forms when plates pull apart?
A rift valley forms when plates pull apart. This results in the Earth's crust stretching and thinning, creating a long, narrow depression with steep walls. Examples include the East African Rift and the Mid-Atlantic Ridge.
