answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

400 amp service what size wire?

A 750 MCM wire with an insulation factor of 90 degrees C is rated at 500 amps. De rated to 80% will allow 400 amps on the wire. A 900 MCM wire with an insulation factor of 75 degrees C is rated at 520 amps. A 1500 MCM wire with an insulation factor of 60 degrees C is rated at 520 amps. Parallel 250 MCM will give you the same usage. A 250 MCM wire with an insulation factor of 75 or 90 degrees C are rated at 255 and 265 respectively. 255 x 2 = 510 x 80% = 408 amps. 265 x 2 = 530 x 80% = 424 amps.


What is the amperage rating for 500 kcm?

The amperage rating for 500 kcmil (thousand circular mils) wire varies based on the type of insulation and installation conditions. For example, in a typical application using THHN insulation, a 500 kcmil copper wire can carry approximately 380-450 amps at 75°C. However, always refer to the National Electrical Code (NEC) and local regulations for precise ampacity ratings based on specific conditions.


How many amps is 500 watts for a jump starter?

To calculate the amps for a jump starter with 500 watts, you can use the formula: Amps = Watts / Volts. If assuming a standard 12-volt car battery, the calculation would be 500 watts / 12 volts = 41.67 amps.


120 volts plus 500 watts equals how many amps?

The formula you are looking for is I = W/E. Amps = Watts/Volts.


Wire size for 500 Amp service?

For a 500 Amp service, the recommended wire size would typically be 4/0 AWG copper or 300 kcmil aluminum. However, it is always best to consult with a qualified electrician to ensure the correct wire size is used based on the specific installation requirements and local electrical codes.

Related Questions

What size wire for 400 amp distribution panel?

For a distribution panel rated at 400 amps parallel runs of 3/0 conductors will do the job.


What minimum size-grounding conductor is required if the circuit protection ahead is rated at 500 amps instantaneous?

For a circuit protection device rated at 500 amps, the minimum size of the grounding conductor is typically determined by the National Electrical Code (NEC) tables. According to NEC Table 250.122, for a circuit with overcurrent protection of 500 amps, the minimum grounding conductor size required is 3/0 AWG copper or 250 kcmil aluminum. Always ensure to check local codes and regulations, as they may have additional requirements.


400 amp service what size wire?

A 750 MCM wire with an insulation factor of 90 degrees C is rated at 500 amps. De rated to 80% will allow 400 amps on the wire. A 900 MCM wire with an insulation factor of 75 degrees C is rated at 520 amps. A 1500 MCM wire with an insulation factor of 60 degrees C is rated at 520 amps. Parallel 250 MCM will give you the same usage. A 250 MCM wire with an insulation factor of 75 or 90 degrees C are rated at 255 and 265 respectively. 255 x 2 = 510 x 80% = 408 amps. 265 x 2 = 530 x 80% = 424 amps.


What size wire is needed for 400 amp 480 volt service?

A 500 MCM wire with an insulation factor of 90 degrees C is rated at 430. Most 400 amp services will use parallel wires on each leg to feed the circuit. A 3/0 wire with an insulation factor of 75 and 90 degrees C is rated at 200 and 225 amps respectively. The insulation rating of these conductors will be 600 volts.


What is the amperage rating for 500 kcm?

The amperage rating for 500 kcmil (thousand circular mils) wire varies based on the type of insulation and installation conditions. For example, in a typical application using THHN insulation, a 500 kcmil copper wire can carry approximately 380-450 amps at 75°C. However, always refer to the National Electrical Code (NEC) and local regulations for precise ampacity ratings based on specific conditions.


500kva how many amps given capacity?

500 KVA how many amps? almost 650 Amps according to formula.


What gauge is 500 amp cable?

A 750 MCM copper conductor with an insulation factor of 90 degrees C is rated at 500 amps.


How many amps does 500 watt halogen pull?

At 120 volts it will pull 4.166 amps. At 240 volts it will pull 2.08 amps.


How many amps is 500 watts for a jump starter?

To calculate the amps for a jump starter with 500 watts, you can use the formula: Amps = Watts / Volts. If assuming a standard 12-volt car battery, the calculation would be 500 watts / 12 volts = 41.67 amps.


120 volts plus 500 watts equals how many amps?

The formula you are looking for is I = W/E. Amps = Watts/Volts.


Wire size for 500 Amp service?

For a 500 Amp service, the recommended wire size would typically be 4/0 AWG copper or 300 kcmil aluminum. However, it is always best to consult with a qualified electrician to ensure the correct wire size is used based on the specific installation requirements and local electrical codes.


How many cold cranking amps for the pt cruiser battery?

500 minimum.