0
How many meters square of 1.1 thickness zincannel steel coil in one ton?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
The thickness of one sheet of steel in a steel casket is how many inches?
Low cost carbon steel caskets are usually made of 20-gauge steel. This means that 20 sheets of 20 ga steel have a thickness of one inch. Twenty-gauge steel sheets have a thickness of 0,8 mm; this is the same thickness as used in many automobile body panels. Standard steel caskets use 18 ga steel sheets which have a thickness of 1 mm. Upper end steel caskets use 16 ga steel sheets with a thickness of 1,3 mm. 16 sheets of 16 ga steel have a thickness of one inch.
What is meant by TMT steel?
True Bar in stainless steel means the manufacture of the bar is rolled on the thickness and the width, attaining a more 90 degree relationship to thickness and width, unlike sheared and edged condition stainless, which is sheared from stainless plate, which offers a rough, usually out of square edge. True bar also may be defined as HRAP (hot rolled annealed and pickled), thus if you see a listing 304/304L HRAP, it is a True Bar, as this is a stainless rolled product.
When a 440 Hz sound is sent through steel a wWhat is the speed of a sound wave that has a wavelength of 1.2 meters and a frequency of 250 Hz?
When a 440 Hz sound is sent through steel, a wavelength of 11.6 meters is measured. What is the velocity of the sound through steel
Is post heating required for carbon steel material above 19.05mm thickness?
It depends on how hot it gets, but if you are talking about welding temperature then most definately.
How much kg of steel need for 10sqft?
None, since there can be no direct conversion.A square foot is a measure of area in 2-dimensional space while a kilogram is a measure of mass. The two measure different characteristics and, according to the most basic principles of dimensional analysis, any attempt at comparisons or conversions between the two are fundamentally flawed.
What is Weight of steel plate per square foot?
That would also depend on the thickness of the steel plate.
What is the unit weight of steel in ton per meter square?
you need the thickness too
How much steel required for 1 square meter slab?
Please specify theGaugeor thickness
What is weight of steel per square feet?
Mass is an attribute of 3-dimensional objects, not 2-dimensional objects. A square foot of steel, with no thickness, cannot exist. Furthermore, the density of steel, depends on the exact composition of the alloy.
The thickness of one sheet of steel in a steel casket is how many inches?
Low cost carbon steel caskets are usually made of 20-gauge steel. This means that 20 sheets of 20 ga steel have a thickness of one inch. Twenty-gauge steel sheets have a thickness of 0,8 mm; this is the same thickness as used in many automobile body panels. Standard steel caskets use 18 ga steel sheets which have a thickness of 1 mm. Upper end steel caskets use 16 ga steel sheets with a thickness of 1,3 mm. 16 sheets of 16 ga steel have a thickness of one inch.
How do you calculate mild steel thickness from stain steel thickness?
By thick control.
What thickness of stainless steel would you need for a tank 25' x 25' x 25' filled with water?
3mm thickness of stainless steel tank. 3mm thickness of stainless steel tank.
What is the weight of steel diamond plate per square foot?
The weight of steel diamond plate per square foot depends on its thickness. Steel diamond plate that is 3/16 inches thick weighs 8.70 pounds per square foot. 3/8" plate weighs 16.35 pounds per square foot.
Square meters in one ton of structural steel?
It is roughly 7.6m2 per ton of steel structure material. This can be used for approximate calculation.
What is 2 gauge steel thickness?
17/64ths of an inch for steel
Can a wolf crush steel in one bite?
A steel can perhaps, but that not steel of any reasonable thickness.
What is the equivalent in inches to 16 gauge steel?
16 gauge standard steel has a thickness of 0.0598 inches. 16 gauge galvanized steel has a thickness of 0.0635 inches.
