0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How many miliamp is 1.5 watts at 12 volts?
1000 milliamperes = 1 amp. Assuming a resistive load, amps = watts / volts = .125 amps or 125 milliamperes
How many amps can a zero gauge wire handle?
You are probably thinking about 1/0 wire (1 ought wire). In copper it is rated at 175 amps and in aluminum 125 amps.
10kw heater at 220V draws how many amps?
45-50 amps. But your overcurrent protection and wire must be designed for 125% of load so the max overcurrent protection is 55 amps or 60
How Many Amps is 1400mA?
watts = amps (times) voltage watts (divided by) voltage = amps 140 (div by) 120 = 1.66 140 (div by) 125 = 1.12
What size wire needed for 100 amp service 700 feet away?
A 400 MCM copper conductor will limit the voltage drop to 3% or less when supplying 100 amps for 700 feet on a 240 volt system. This size will allow the conductor to be loaded to 80 amps. 100 x 80% = 80 amps. Conductors are only allowed to be loaded to 80% or their rated capacity. If you need the full 100 amps then you would need to use a wire with a rating of 125 amps. 125 x 80% = 100 amps. A 600 MCM copper conductor will limit the voltage drop to 3% or less when supplying 125 amps for 700 feet on a 240 volt system.
How many amps can be put on a 125 amp service?
You should not load a 125 amp panel any more than 100 amps.
How many amps is 2 wire good for?
depends on its use. If its for residential service its good for 125 amps In commercial and industrial installations it's a bit more complicated but you end up at the same 125 amps.
How many amps is 2 gauge wire good for?
depends on its use. If its for residential service its good for 125 amps In commercial and industrial installations it's a bit more complicated but you end up at the same 125 amps.
How many miliamp is 1.5 watts at 12 volts?
1000 milliamperes = 1 amp. Assuming a resistive load, amps = watts / volts = .125 amps or 125 milliamperes
Can you replace 2.5 Amps 125 Volts with 10 Amps 125 Volts?
You physically can but sit will be unsafe, and will not protect the circuit because it will not blow when it should. Only replace a fuse with the same size fuse.
What size aluminum wire to feed 125 Amps 220 volt a distance of 175' and what size ground?
A 3/0 aluminum conductor will limit the voltage drop to3% or less when supplying 125 amps for 175 feet on a 220 volt system. If the 125 amp load is a sub distribution panel that is not going to be fully loaded to 125 amps then using the exact connected load, which might be smaller than 125 amps will effect the wire sizing. The grounding conductor for that size distribution panel is #6 bare copper.
What size wire and breaker for a 30 hp 240 volt 3 phrase motor?
A three phase 30 HP at 240 volts draws 80 amps. Motor feeders have to be rated at 125% of the motors full load amps. 80 x 125% = 100 amps. A # 3 copper conductor with an insulation factor of 75 or 90 degrees C are rated at 100 and 105 amps respectively. Non-time delay fusing is 225 amps, time delay fusing is 125 amps and a circuit breaker is sized by 250% x 80, the full load amps, which equals 200 amps.
How do you convert 240 volts to 125 kVA?
To answer this question a current value needs to be given. 125000 is the product of amps times volts. I = W/E = 521 amps. So to bring 240 volts up to 125 KVA you need the circuit load to draw 521 amps.
How many amps can a zero gauge wire handle?
You are probably thinking about 1/0 wire (1 ought wire). In copper it is rated at 175 amps and in aluminum 125 amps.
What is the cable size for motor 15kw 440 volts connection?
The current draw is about 27 amps. A motor feeder has to be 125% of the motors full load amperage. 27 x 125% = 33 amps. A #8 copper conductor with an insulation factor of 90 degrees C is rated at 40 amps.
10kw heater at 220V draws how many amps?
45-50 amps. But your overcurrent protection and wire must be designed for 125% of load so the max overcurrent protection is 55 amps or 60
How Many Amps is 1400mA?
watts = amps (times) voltage watts (divided by) voltage = amps 140 (div by) 120 = 1.66 140 (div by) 125 = 1.12
