0
How much is it worth Smith weston 37 niquel plate wood grip revolver?
Wiki User
∙ 11y ago
50-325 usd
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you dismantle a S and W mod 19.3?
A Smith and Wesson model 19-3 is a .357 magnum revolver, six shot, blued, the 3 means third change. To dismantle the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left. When the grips are removed the side plate will be fully visible. Remove the 3 screws from the side plate. To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit. Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off, so be sure it falls on a padded surface. At this point most internal parts will be visible and accessible. To reassemble the revolver, do the above in reverse, making sure the hammer block is in place and the side plate seats correctly. You can tap on the side plate with a wood or plastic tool to seat it properly. Replace the screws in the correct place along with the grips and grip screw.
How do you disassemble a smith and Wesson model MP?
A Smith and Wesson M&P model is a 6 shot revolver in 38 Smith & Wesson Special caliber. The MP or M&P stands for "military and police".To disassemble the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left.When the grips are removed the side plate will be fully visible.Remove the screws from the side plate.To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit.Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off along with the hammer block, so be sure it falls on a padded surface.At this point most internal parts will be visible and accessible.The cylinder can be removed by sliding the cylinder crane to the left and out of the frame, while holding the cylinder in place.The cylinder will now be free.To reassemble the revolver, do the above in reverse, making sure the hammer block is in place and the side plate seats correctly.You can tap on the side plate with a wood or plastic tool to seat it properly.Replace the cylinder crane and cylinder. Be sure the correct screw is used to hold the cylinder crane to the frame.Replace the remaining side plate screws in the correct place along with the grips and grip screw.Holding back the hammer slightly, or with the hammer cocked, look in the gap between the hammer and frame to be sure the hammer block has been replaced.A word of caution here: know exactly what you are doing before making alterations or repairs. Revolvers are delicate and expensive machinery.
Where is the serial number on a Iver Johnson revolver?
under the grip plate
How do you disassemble a Smith and Wesson model 66?
The Smith And Wesson model 66 is a 357 magnum caliber, 6 shot revolver of stainless steel constructionTo disassemble the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left.When the grips are removed the side plate will be fully visible.Remove the screws from the side plate.To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit.Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off along with the hammer block, so be sure it falls on a padded surface.At this point most internal parts will be visible and accessible.The cylinder can be removed by sliding the cylinder crane to the left and out of the frame, while holding the cylinder in place.The cylinder will now be free.Removal of the extractor rod and extractor will not be described here, but the extractor rod is threaded in reverse to prevent loosening while operating. Caution: The extractor rod assembly is very often damaged in attempts to unscrew it. Also, it is necessary to support the extractor while unscrewing the extractor rod.To reassemble the revolver, do the above in reverse, making sure the hammer block is in place and the side plate seats correctly.You can tap on the side plate with a wood or plastic tool to seat it properly.Replace the cylinder crane and cylinder. Be sure the correct screw is used to hold the cylinder crane to the frame.Replace the remaining side plate screws in the correct place along with the grips and grip screw.Holding back the hammer slightly, or with the hammer cocked, look in the gap between the hammer and frame to be sure the hammer block has been replaced.A word of caution here: before making alterations or repairs know exactly what you are doing. Revolvers are delicate and expensive machinery.
How do you disassemble a Smith and Wesson revolver?
The Smith and Wesson J, K, L and N frame revolvers share the same basic procedure for disassembly and reassembly.To disassemble the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left.When the grips are removed the side plate will be fully visible.Remove the screws from the side plate.To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit.Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off along with the hammer block, so be sure it falls on a padded surface.At this point most internal parts will be visible and accessible.The cylinder can be removed by sliding the cylinder crane to the left and out of the frame, while holding the cylinder in place.The cylinder will now be free.Removal of the extractor rod and extractor will not be described here, but the extractor rod is threaded in reverse to prevent loosening while operating. Caution: The extractor rod assembly is very often damaged in attempts to unscrew it. Also, it is necessary to support the extractor while unscrewing the extractor rod.To reassemble the revolver, do the above in reverse, making sure the hammer block has been replaced and the side plate seats correctly.You can tap on the side plate with a wood or plastic tool to seat it properly.Replace the cylinder crane and cylinder. Be sure the correct screw is used to hold the cylinder crane to the frame.Replace the remaining side plate screws in the correct place along with the grips and grip screw.Holding back the hammer slightly, or with the hammer cocked, look in the gap between the hammer and frame to be sure the hammer block has been replaced. If not the side plate must be removed again and the hammer block must be added.A word of caution here: before making alterations or repairs know exactly what you are doing. Revolvers are delicate and expensive machinery.
How can you disassemble a Smith and Wesson J K L or N frame revolver?
The Smith and Wesson J, K, L and N frame revolvers share the same basic procedure for disassembly and reassembly.To disassemble the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left.When the grips are removed the side plate will be fully visible.Remove the screws from the side plate.To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit.Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off along with the hammer block, so be sure it falls on a padded surface.At this point most internal parts will be visible and accessible.The cylinder can be removed by sliding the cylinder crane to the left and out of the frame, while holding the cylinder in place.The cylinder will now be free.Removal of the extractor rod and extractor will not be described here, but the extractor rod is threaded in reverse to prevent loosening while operating. Caution: The extractor rod assembly is very often damaged in attempts to unscrew it. Also, it is necessary to support the extractor while unscrewing the extractor rod.To reassemble the revolver, do the above in reverse, making sure the hammer block has been replaced and the side plate seats correctly.You can tap on the side plate with a wood or plastic tool to seat it properly.Replace the cylinder crane and cylinder. Be sure the correct screw is used to hold the cylinder crane to the frame.Replace the remaining side plate screws in the correct place along with the grips and grip screw.Holding back the hammer slightly, or with the hammer cocked, look in the gap between the hammer and frame to be sure the hammer block has been replaced. If not the side plate must be removed again and the hammer block must be added.A word of caution here: before making alterations or repairs know exactly what you are doing. Revolvers are delicate and expensive machinery.
How do you disassemble a Smith Wesson model 66-4?
1. Request an owner's manual from Smith and Wesson.2. The owners manual no longer contains disassembly instructions, probably because of liability reasons. Nor is a parts list and exploded diagram packed with the weapon as it used to be.It is interesting that in the past, before 1990, a small screwdriver that fit both the side plate screws and grip screw was packed with most revolvers from Smith and Wesson. These were not just for adjusting sights as they were packed with fixed sight revolvers.A Smith and Wesson model 66-4 is a .357 magnum 6 shot K frame revolver of stainless steel construction. The -4 means fourth change.The Smith and Wesson J, K, L and N frame revolvers share the same basic procedure for disassembly and reassembly.To disassemble the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left.When the grips are removed the side plate will be fully visible.Remove the screws from the side plate.To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit.Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off along with the hammer block, so be sure it falls on a padded surface.At this point most internal parts will be visible and accessible.The cylinder can be removed by sliding the cylinder crane to the left and out of the frame, while holding the cylinder in place.The cylinder will now be free.Removal of the extractor rod and extractor will not be described here, but the extractor rod is threaded in reverse to prevent loosening while operating. Caution: The extractor rod assembly is very often damaged in attempts to unscrew it. Also, it is necessary to support the extractor while unscrewing the extractor rod.To reassemble the revolver, do the above in reverse, making sure the hammer block has been replaced and the side plate seats correctly.You can tap on the side plate with a wood or plastic tool to seat it properly.Replace the cylinder crane and cylinder. Be sure the correct screw is used to hold the cylinder crane to the frame.Replace the remaining side plate screws in the correct place along with the grips and grip screw.Holding back the hammer slightly, or with the hammer cocked, look in the gap between the hammer and frame to be sure the hammer block has been replaced. If not the side plate must be removed again and the hammer block must be added.A word of caution here: before making alterations or repairs know exactly what you are doing. Revolvers are delicate and expensive machinery.
Colt 357 mark III revolver nickel plate worth?
A Colt .357 Mark III nickel plated revolver is worth between $500 and $750. The actual value varies greatly based on the gun's overall condition.
I want to renickle plate a revolver?
Elite Custom Guns can replate or refinish your weaponry. They are in Indiana and can be reached online at: www.elitecustomguns.com or by phone at (704)821-6406.
What has the author Jared Smith written?
Jared Smith has written: 'Walking the perimeters of the plate glass window factory' 'Dark Wing' 'Where Images Become Imbued With Time'
What should you smith to get the best experience for each bar you use in runescape for f2p?
Steel Plate Bodys
How do you take apart smith and Wesson 22 revolver?
You do not have to take apart the revolver to clean the cylinders and barrel or external parts.If the internal parts are very dirty or contain gummed up oil or grease then it may have to be taken apart for cleaning.More damage is done to .22 caliber guns from improper cleaning than shooting. Protect the muzzle when cleaning.Do not dry fire .22 handguns as the firing pin can cause damage without a cartridge to cushion it.The owners manual no longer contains disassembly instructions, probably because of liability reasons.Nor is a parts list and exploded diagram packed with the weapon as it used to be.Smith and Wesson .22 caliber revolvers are J and K frame types.The Smith and Wesson J, K, L and N frame revolvers share the same basic procedure for disassembly and reassembly.To disassemble the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left.When the grips are removed the side plate will be fully visible.Remove the screws from the side plate.To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit.Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off along with the hammer block, so be sure it falls on a padded surface.At this point most internal parts will be visible and accessible.The cylinder can be removed by sliding the cylinder crane to the left and out of the frame, while holding the cylinder in place.The cylinder will now be free.Removal of the extractor rod and extractor will not be described here, but the extractor rod is threaded in reverse to prevent loosening while operating. Caution: The extractor rod assembly is very often damaged in attempts to unscrew it. Also, it is necessary to support the extractor while unscrewing the extractor rod.To reassemble the revolver, do the above in reverse, making sure the hammer block has been replaced and the side plate seats correctly.You can tap on the side plate with a wood or plastic tool to seat it properly.Replace the cylinder crane and cylinder. Be sure the correct screw is used to hold the cylinder crane to the frame.Replace the remaining side plate screws in the correct place along with the grips and grip screw.Holding back the hammer slightly, or with the hammer cocked, look in the gap between the hammer and frame to be sure the hammer block has been replaced. If not the side plate must be removed again and the hammer block must be added.A word of caution here: before making alterations or repairs know exactly what you are doing. Revolvers are delicate and expensive machinery.
