There is no lead in PVC. It's plastic made from chlorine. There actually IS lead in PVC, or tin, or some other metal salt. It's a stabilizer. If they don't put a stabilizer in PVC, it eventually disintegrates. As to how much lead there is in it...who's to say? A little goes a very long way here. I think it would take a great deal of it to be toxic through the skin...if your kid sucked on the insulation that would be a different story, but children shouldn't gnaw electric wiring in the first place.
When selecting a material for an insulation factor it has to be balanced between flexibility and its insulation properties. Glass would be an excellent insulator but in the electrical field hard to pull through conduit and bending without damaging the insulation. Cross-linked polyethylene fits both the conditions for a wire insulation. The insulation has a high insulation factor plus the ability to bend without damaging the insulation and can operate in a 90 degree C temperature range.
A non-metal, butlook inyour science book. :)
Not that I know of. When insulation is applied to wire it is extruded so that the insulating material is uniform around the conductor. Without this uniformity the conductors insulation factor would vary and the wire would have to be rated at the lowest reading factor when tested with a high voltage. Even when splicing a wire, the electrical code states that the insulation covering the splice has to be brought up to or surpass the insulation factor that is supplied by the manufacturer of the wire.
A neuron is analogous to an electric wire. If you look at an electric wire going from a lamp to a wall plug, you do not see the actual wire. Instead, you see the insulation. If you would scrape off the insulation, you would see two wires. If those two wires touched you would hear a loud pop. Then a circuit breaker would throw. The wire would be just as good as it was before you removed the insulation. The wire carried the electricity. The insulation protected the wire and let it do its job. Without the insulation, the bulb would not work. The Myelin sheath protects the nerve from outside forces. It lets it carry its signal free from outside influence. It is a piece of insulation.
You could, but it's certainly not a good idea. Any damage to the insulation of the wires running through it would be extremely dangerous.
An insulation material is one which separates one region from another. Common uses would be electrical insulation, thermal insulation, and acoustic insulation.
Insulation tape is used to protect exposed electrical conductors or wires. Another term for it would be electrical tape. It is wrapped around wires and other electrical conductors to protect them.
This would depend on the type used. In newer homes, soy or bio-based spray insulation is being used that is non-toxic and earth friendly. But that is nowhere near the norm. Most spray foam insulation is made from toxic chemicals and can be very harmful if ingested.
When selecting a material for an insulation factor it has to be balanced between flexibility and its insulation properties. Glass would be an excellent insulator but in the electrical field hard to pull through conduit and bending without damaging the insulation. Cross-linked polyethylene fits both the conditions for a wire insulation. The insulation has a high insulation factor plus the ability to bend without damaging the insulation and can operate in a 90 degree C temperature range.
nonmetals are the best insulators
j
Lung cancer is caused by an exposure to certain carcinogens- cancer causing things. ONE of those tinhs is asbestos. At one time, SOME electrical wiring was insulated with asbestos, as well as building insulation, dry wall mud, plaster, etc that an electrician would disturb. While it would be POSSIBLE to have an occupational exposure to lung cancer, for an electrician it would be pretty remote.
A non-metal, butlook inyour science book. :)
Heat insulation would be wool. Note that denim is normally made of cotton, or a cotton/polyester blend. None of them would be very good electrical insulation when wet.
Heat insulation would be wool. Note that denim is normally made of cotton, or a cotton/polyester blend. None of them would be very good electrical insulation when wet.
Without insulation on the electrical wiring that we use, there would be the constant concern that the electrical wires would touch each other. This touching of different potentials could cause sparking or fuses or breakers needlessly tripping. The labour of installation would become much higher as the workmanship to individually separate each individual wire from each other would drive the costs up considerably. With insulation installed on the wires these concerns are now invalid.
Not that I know of. When insulation is applied to wire it is extruded so that the insulating material is uniform around the conductor. Without this uniformity the conductors insulation factor would vary and the wire would have to be rated at the lowest reading factor when tested with a high voltage. Even when splicing a wire, the electrical code states that the insulation covering the splice has to be brought up to or surpass the insulation factor that is supplied by the manufacturer of the wire.