answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered
2006-07-11 18:06:25
2006-07-11 18:06:25

Diameter x Diamater X Depth X 5.2

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Above ground pumps have to be gravity fed, and the in ground pumps pull a vacuum and draw the water to them.


If this is for an above ground swimming pool, I would level the ground before putting up the pool. Otherwise, the weight of the water might collapse one of the walls of the pool.


Probabily the ground surrounding your pool if its in-ground. In an above-ground pool they most likely fly into the pool or crawl into it from the sides.


Yes , it filters out the water taking out any bugs or so while cleaning the water.


Not exactly. The high winds can, however, spray some water out of a swimming pool. A tornado can also damage the walls of above ground pools, causing water to spill out.


24' x 4' round above ground holds 14,000 gallons


Get the garden hose, run it from the pool to a drain and siphon the water out.


319.2 gallons for every inch the water in it is deep.




17,205 gallon refer to www.backyardcitypools.com/swimming-pools/pool-volume-calculate.com



Proper water chemistry instead of neglect. Long filter periods and a clean filter.


Absolutely, just like an in ground pool, leaves, bugs, etc can get into it. A pool cover is just to protect the pool water from those sorts of things.


Not so much the pool or the water but it will plug the filter in no time at all thus reducing the quality of the water and the chlorine levels.


if it's the right size for your pool, it will "stick" to the water and not blow off.


You need to provide information on the area of the pool as well.


gravity level is water (or swimming) is half as much gravity as when you're on solid ground.


fog is droplets of water vapor suspended into air above ground.


As the aqueducts in the city of Rome were above ground, they were designed with arches to carry the water pipe.As the aqueducts in the city of Rome were above ground, they were designed with arches to carry the water pipe.As the aqueducts in the city of Rome were above ground, they were designed with arches to carry the water pipe.As the aqueducts in the city of Rome were above ground, they were designed with arches to carry the water pipe.As the aqueducts in the city of Rome were above ground, they were designed with arches to carry the water pipe.As the aqueducts in the city of Rome were above ground, they were designed with arches to carry the water pipe.As the aqueducts in the city of Rome were above ground, they were designed with arches to carry the water pipe.As the aqueducts in the city of Rome were above ground, they were designed with arches to carry the water pipe.As the aqueducts in the city of Rome were above ground, they were designed with arches to carry the water pipe.


You can fill a standard in-ground swimming pool.


An 18' Round 52" wall above ground pool holds approximately 7300 gallons



In simplest terms, an above ground pool pump is a flooded suction pump, which means the water level must be higher than the pump for it to operate, and an inground pump has the ability to draw water up from a level lower than the pump. The engineering and structure of these two different types of pumps is what makes them work the way they do. This means that, in a typical installation, you could use an inground-specific pump on an above ground pool, but not an above ground pump on an inground pool with the water level below the pump.


To install the water return fitting above the ground pool, you have to switch off the source. After this you can then install the water.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.