0
It is hard to understand what this question is actually asking... The answer to the Related Question shown below: "http://wiki.answers.com/Q/How_do_you_wire_a_new_light_with_an_on-off_switch_using_wires_coming_from_an_outlet?" might be of some help, perhaps?
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is the difference between single pole switch and a three way?
A single pole switch controls a light or outlet at one location. A 3 way switch controls a light or outlet from 2 locations.
Can a hps light fixture be plugged in to a regular outlet?
If the ballast of the HPS fixture has a 120 volt tap then, yes it can be plugged into a 120 volt receptacle.
How do you know which outlet is controlled by a switch?
Plug a lamp into a working socket of an outlet to ensure the lamp works. Then turn off the switch and plug lamp into all outlet sockets, top and bottom outlets until the lamp doesn't light. Then turn on the switch and the lamp should light. Often a switch in a bedroom is only connected to one socket in a duplex outlet. It is possible to remove a jumper in an outlet to isolate the sockets for just this purpose. Often an electrician will install the outlet upside down (The third prong pointing up, to identify the outlet.
Why is there no power to outlet when light switch is turned off?
Some rooms have an outlet controlled by a light switch at the door. This is normally in bedrooms. It is possible that the switch is wired to only one of two outlets in a duplex outlet since it is easy to configure a duplex outlet to separate the bottom and top outlets.
How do you disconnect a light switch and outlet that are tied together?
If there is a black wire going from the outlet to the switch and the other side of the switch goes back to the outlet then just cut these wires and connect supply wire directly to outlet. If the supply goes to the switch first, disconnect from switch and connect the two wires with a wire-nut. Some situations only switch one of the two outlets in a duplex device. Do the same thing, but also replace the outlet since the strapping between both outlets has been removed.
Does an outlet controlled by a light switch still pull energy when the light switch is off?
No.
What if your Dodge Durango 2004 head light on n off on n off?
then you need to stop flicking the light switch
How is a fluorescent light bulb connected to an outlet?
Generally with a cord and just plugged in.
How much does it cost when you turn a light switch on and off?
Mythbusters actually proved that flicking the light switch on and off didn't cost any more than 2 cents.
Why does the light switch not work to an existing electrical outlet?
Could be a loose connection somewhere, or a bad switch, or a bad outlet.
Can you change an electrical outlet into a switch for a light?
Sure. For a light you need a fixture to hold the light and the light itself. The light needs to be connected to a voltage supply which you can get from the outlet. In the outlet box you will have a black, white and bare ground wire. Essentially you connect the white and bare wires directly to the light and switch the black wire (hot) through a switch.
What is the difference between single pole switch and a three way?
A single pole switch controls a light or outlet at one location. A 3 way switch controls a light or outlet from 2 locations.
Can a hps light fixture be plugged in to a regular outlet?
If the ballast of the HPS fixture has a 120 volt tap then, yes it can be plugged into a 120 volt receptacle.
Have a wall outlet that when you turn the light switch on the outlet has no power need help?
Change the wall outlets
Why does your ipod not charge when you have been charging it for days?
if you are plugging it into your cp, it might be blocking your ipod charger usage, or if you plugged it into the wall, then you might have to turn on a light switch to actually make it charge, or if you plugged it into a multi-outlet-extender-thingy, then you might just have to turn the multi-outlet-extender-thingy on, and if none of that works, there might be a problem with the charger. hope i could help.
How do you run a light with a switch from a existing outlet with out controlling the out let with the switch?
Break off the tab that jumps between the wire mounting screws on the side of the receptacle. This turns one receptacle into 2 seperately controlled parts--one is always hot and the other is controlled by the switch (the one with the lamp plugged in).
How do you wire one light and one GFCI and another light light and fan with two switches and one power line?
Connect the incoming power to the line side of the GFCi outlet. Now run another wire connected to the line side of the GFCI outlet from the GFCI outlet to the switches. Power one of the switches and use that switch to turn on the 2 lights. Run power from that switch to another switch and use that switch to send power to the fan. Mount both switches in a double pole switch box. If the light above the sink has an outlet on it then you will have to connect power going to that light on the load side of the GFCI outlet. If not then just connect it to the line side.
