answersLogoWhite

0

If the ballast of the HPS fixture has a 120 volt tap then, yes it can be plugged into a 120 volt receptacle.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How do you cap off the outlet if you are replacing a bathroom light fixture but the old one had an electrical outlet?

Answer for USA, Canada and countries running a 60 Hz supply service.By asking this question you are probably not quite ready to take on this particular task. The correct answer to your question will depend on the exact location of the light fixture.If your bathroom light fixture has an outlet in it you will need to make sure that the entire bathroom's electrical circuits are protected by a GFCI circuit breaker. Many homes built before the 1980s have bathrooms which are not protected by a GFCI because the wiring code applicable back then did not require it.If the old light has a built-in outlet you will not need to cap the outlet because it will be removed along with the lighting fixture.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


What is a light fixture?

A fixture or device that holds a light in place by means of some sort of socket, that is connected to a power source.


What is a pin based fluorescent light fixture?

A pin based fluorescent light fixture is the type of fixture that takes fluorescent tubes. On each end of the fluorescent tubes there are contact pins. These pins are used to hold the tube in the fixture and to supply the voltage to the tube from the fixture's ballast.


What happens if a light fixture overheats?

it will explode


How to turn light plugged into outlet on by flicking switch?

It is hard to understand what this question is actually asking... The answer to the Related Question shown below: "http://wiki.answers.com/Q/How_do_you_wire_a_new_light_with_an_on-off_switch_using_wires_coming_from_an_outlet?" might be of some help, perhaps?

Related Questions

How can I wire an outlet from a light fixture?

To wire an outlet from a light fixture, you will need to connect the outlet to the wiring of the light fixture. This involves running a new wire from the light fixture to the outlet, making sure to follow proper electrical safety procedures and regulations. It is recommended to consult a licensed electrician for assistance to ensure the job is done correctly and safely.


Can a neon light be plugged into the wall?

(im the one asking ^That^ Question BTW) the kind of lights these are, are the kind you would install under your car... i have 3 tubes with wires at the end of each, a switch but no transformer do i need it? And also can i just stick the wires into the outlet or would that kill me? Ahaha Thank You Everyone!


How can I convert a light fixture to an outlet?

To convert a light fixture to an outlet, you will need to disconnect the wires from the light fixture and connect them to an outlet instead. This may require some electrical knowledge and tools. It is recommended to consult a professional electrician for safety and proper installation.


What are some important factors to consider when choosing a bathroom light fixture with an outlet?

When choosing a bathroom light fixture with an outlet, consider factors such as the fixture's design and style, the amount of light it provides, the outlet's location and compatibility with your needs, and the fixture's safety features to ensure it meets electrical codes and regulations.


How can I change a light fixture to an outlet?

To change a light fixture to an outlet, you will need to turn off the power to the circuit, remove the existing light fixture, install a new electrical box, connect the wires to the outlet, and secure the outlet in place. It is important to follow safety precautions and consult a professional if needed.


What is the proper installation method for an outlet box for a light fixture?

To properly install an outlet box for a light fixture, first turn off the power to the area. Then, choose a location on the ceiling or wall where the light fixture will be installed. Next, mark the spot and cut a hole for the outlet box. Secure the outlet box in place using screws or nails. Finally, connect the wiring from the outlet box to the light fixture following the manufacturer's instructions.


What are some important considerations to keep in mind when selecting an exterior light fixture with an outlet?

When selecting an exterior light fixture with an outlet, important considerations include the fixture's durability, weather resistance, compatibility with your existing electrical setup, and the location of the outlet for convenient use.


How can I convert a light fixture into an outlet?

Converting a light fixture into an outlet involves disconnecting the wires from the fixture and connecting them to an outlet. You may need to install a junction box and follow electrical safety guidelines. It is recommended to consult a licensed electrician for this task to ensure proper installation and safety.


How can I add an outlet to a light fixture?

To add an outlet to a light fixture, you will need to run a new electrical wire from the existing light fixture to the location where you want the outlet. This involves turning off the power, cutting into the wall to access the wiring, connecting the new wire to the existing wiring, and installing the outlet box and outlet. It is important to follow all safety precautions and local building codes when doing electrical work. If you are not comfortable with electrical work, it is recommended to hire a licensed electrician.


How is a fluorescent light bulb connected to an outlet?

Generally with a cord and just plugged in.


What is a swag lamp?

A swag lamp is a light fixture that is hung from one or more hooks from the ceiling and is usually plugged into a wall receptacle. They were used in homes in the 70's for decorative lighting fixtures. Heavy scene man.


How can I install a plug-in outdoor light in my backyard?

To install a plug-in outdoor light in your backyard, follow these steps: Choose a suitable location for the light near an outdoor electrical outlet. Mount the light fixture securely using screws or brackets. Connect the light fixture to the outdoor electrical outlet using a weatherproof extension cord. Plug the extension cord into the outlet and test the light to ensure it is working properly. Make sure to follow all safety precautions and consult a professional if needed.