0
What else can I help you with?
Can you use 8 ohm speakers on a 10 ohm radio?
Never haerd of a 10 ohm radio. There is no 10 ohm radio amplifier on the market, when you think that must be the output impedance of the amplifier. The output impedance of a radio amp is always less than 0.5 ohms. Scroll down to related links and go to "Voltage Bridging or impedance bridging - Zout < Zin"
2ohm mono amp and one 15 inch 4 ohm wooferwoofer can go down to 5 ohm how do you wire and will anything be damaged?
Hook it up. You must know: There is no 2 ohm mono amplifier. All audio amplifiers have an output impedance of smaller than 0.5 ohms. So we use impedance bridging. Scroll down to related links and look at "Impedance bridging".
How do you connect a 2 ohm amplifier to a 4 ohm speaker?
Yes you can. 2 ohms is as low as you can go with that amp MOST car subs have 4 ohm voice coils. The bigger the number, the less low bass frequency run two single voice coils subs and you'll be fine. It's a myth. There is really no 2 Ohm amplifier on the market. And there never was. The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout << Zin. That means the output impedance of the amplifier is much less than the input impedance of the loud speaker. The damping factor Df = Zin / Zout tells you what Zout is. Zout = Zin/Df. If the damping factor Df = 200 and the loudspeaker impedance is Zin = 4 ohms, the output impedance of the amplifier is Zout = 4 / 200 = 0.02 ohms. You see, there is no "2 ohm amplifier" on the market with a 2 ohm output impedance. Scroll down to related links and look at "Voltage Bridging or impedance bridging - Zout < Zin".
2ohm mono amp1000 watt RMS and one 15 inch duel voice coil..4 ohm woofer can go down to .5 ohm but is 4ohm..how do you wire and will anything be damaged?
Hook it up. Nothing will be damaged. It's a myth. There is no 2 ohm amp on the market and there never was. Your amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout
Can resistance be added to speakers to make a 4 ohm speaker have an 8 ohm load?
You "can" add a four ohm resistor in series with a four ohm speaker, and make it look like an eight ohm speaker, however, the frequency response will not be the same. It is better to use to correct speaker for the amplifier, or use two four ohm speakers in parallel. That resistors power rating must exceed the rating of the speaker. Half the from the amplifier will go to the speaker, while half will go to the resistor, making it get quite hot.
Will a 4 ohm amp work with a 8 ohm receiver?
Yes, if you use two 4 ohm speakers or or one 4 ohm resistor and a 4 ohm speaker to equal the 8 ohm resistance per channel. An important thing to note about this, is that you will need to make sure you get a resistor that can handle the current. You can go higher in resistance but not lower, it must be equal to or higher. Something important is added: The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout
What size amp do i need for two 10 inch kicker comp's?
You could go with a 600 watt 2 ch amp or a 300 watt mono block amp, depends on what OHM the subs are, if they are 8 ohm you could wire them down to 4 ohm or if they 4 ohm u could wire them to 2 ohm, i have a 600.1 Boss amp and subs are wired together at 2 ohm and they BANG.
Where might one go to obtain a bridging loan in the UK?
Bridging Loans can be obtained from Fincorp, a group comprised of three gentlemen named Ronnie Natas, Matthew Anderson and Nigel Alexander. The address is 58 Acadia Road, London NW8 68G and the company phone number is 020-7722-7547 and the email address is bridging@fincorp.co.uk.
If the voltage of a battery was increased what would happen to the light bulbs brightness?
Yes it would start glowing more brightly but at a certain point it would burn ou if you go on increasing the power.
What same word goes before over page and gap?
The word that can go before both "over page" and "gap" is "bridging."
Can a 1 ohm auto speaker be replaced with a 4 ohm auto speaker?
Yes It can be. But can your amp handle a 1 ohm load? you can go to this web site www.the12volt.com They have load calculator's and also you can ask the car audio gods any questions and the will answer all you questions for FREE....
How do you hook three 2omh kicker subs at 1 ohm?
You can go to Kicker.com for the wiring diagrams for your sub.
