0
I been struggling with this too. I beleive that it makes no economic or logical sense to construct a steam powered turbine generator until you hit a minimum of 500kw. The componets needed to run any such unit, steal too much power from the gross output of the unit as you go small scale, example 20kw. It would be great to build a small unit as such that could power and heat your home off of wood, coal, or other combustible materials. But consider the following: you need a furnace(Iduction draft and forced draft fans=negative watts)-boiler-(boiler water circulating pumps) - you need to deal somewhat with water chemistry-you need a condenser; that requires a source of cool water which requires a circulating pump(negative watts)- you need a feedwater pump(negative watts)- oil pumps for the turbine bearings(negative watts)-systems to feed fuel to the furnace(conveyor motors-(negative watts). All things considered you only get about 40% thermal effeciency from a "Rankin Cycle" boiler/furnace. You would burn too much fuel.
What else can I help you with?
How do fossil fuel burning plants work?
Simple breakdown of how Gas station works.Water is taken from a local river, this is then cleaned up, and given a neutral PH level. The gas is burned in what is known as a boiler. There are many tubes within the boiler which all carry the water. The water is heated to such an extent that it turns to steam, and we use this steam to turn what is known as a Turbine. The turbine on a Gas station would be a GT or Gas Turbine. This turbine is attached to what is Known as an AC generator. Similar to a car Alternator, but much larger. A generator turns Mechanical movement into Electricity through Electromagnets.This electricity is then put through a transformer which would step it up to around 132Kv, where it would then be fed to a consumer.WATER BOILER STEAM TURBINE GENERATOR ELECTRICTY
Why would you not heat the steam coming out of turbine and feedback to turbine?
Steam is redirected back into the boiler from the high-pressure turbine for reheating, but the steam from the low-pressure turbine enters into a condenser to become water again.
How can I make a wood-fired electric generator?
To make a wood-fired electric generator, you would need to build a combustion chamber to burn the wood and produce heat. This heat would then be used to boil water and create steam, which would turn a turbine connected to an electric generator. The generator would then convert the mechanical energy from the turbine into electrical energy. It is important to ensure safety measures are in place when working with fire and electricity.
What are the last 2 steps in an electrical power plant?
The last two steps are:The steam or gas spins the turbinesthe turbines then turns the electric generators producing elecricity
What are the three main sources of electricity?
My answer would be battery (or chemical), generator, and solar. Not sure what your context is. If you are asking about what's used in power plants, like coal, nuclear, and...I guess oil/natural gas would be the third, those are just different sources of heat to produce steam that turns a steam turbine. In all these cases it's still a generator.
How do geothermal power plants generate electricity?
Geothermal power plants work in one of two ways.One way is that they drill wells into a geothermal reservoir and extract steam to be used in a turbine. If the reservoir is not quite hot enough, they might have to extract hot water, and flash it into steam by lowering the pressure. In either case, this steam is run through a turbine, which turns a generator to generate electricity. The steam is usually condensed and either used in the plant or reinjected into the ground.The other way some plants work is by using the geothermal steam to heat water contained in a closed loop. This water is turned into steam, and runs the turbine. The steam from the ground would be condensed and reinjected. This has the advantage of keeping the geothermal steam separate from the power plant.Note that other than the source of the steam, a geothermal power plant operates in much the same way most other power plants work. Using steam to turn a turbine, which turns a generator is a very common method. Notable exceptions would be wind farms, solar cells, and hydropower dams, among others.
How do geothermal power generate electricity?
Geothermal power plants work in one of two ways.One way is that they drill wells into a geothermal reservoir and extract steam to be used in a turbine. If the reservoir is not quite hot enough, they might have to extract hot water, and flash it into steam by lowering the pressure. In either case, this steam is run through a turbine, which turns a generator to generate electricity. The steam is usually condensed and either used in the plant or reinjected into the ground.The other way some plants work is by using the geothermal steam to heat water contained in a closed loop. This water is turned into steam, and runs the turbine. The steam from the ground would be condensed and reinjected. This has the advantage of keeping the geothermal steam separate from the power plant.Note that other than the source of the steam, a geothermal power plant operates in much the same way most other power plants work. Using steam to turn a turbine, which turns a generator is a very common method. Notable exceptions would be wind farms, solar cells, and hydropower dams, among others.
Where can I buy a steam powered generator?
The best place to purchase a steam powered generator would be online at www.greensteamengine.com. The website is very valuable to show the advantages of going with steam power.
Where are the requirements for steam turbine maintenance jobs?
To find out more about steam turbine maintenance jobs specifications one would be advised to contact specialists from recruitment agencies or job centers.
Where can I get a steam powered generator?
The best place to get a steam powered generator nowadays would be on Amazon.com/.ca. They may be a bit pricey, but they usually are a good investment.
How is steam used to create energy?
The steam can be used to turn turbines that in turn generate electricity. The steam is generated by burning coal or some other fossil fuel, or nuclear power. ------------------------------------------------------------------------------------------------ Steam under high pressure and high temperature would have pressure energy and thermal energy. As energy can neither be created nor be destroyed and could be changed from one form into another, these form of energy is utilized to run the turbine to generate electrical energy. In olden days steam was utilized to activate the piston in the cylinder and there by rotate the wheels of the rail engine. This is how the energy right from steam being used.
How do turbines and generators work together to make electrical energy?
Turbines are linked to the generators on a common shaft. The turbines are turned by steam (in the case of nuclear, coal, or biomass power plants), by water (in the case of hydroelectric power plants), or by wind (windmills). The turbine then turns the generator, which creates electricity. Think of blowing on a fan. Your "wind" is turning the blades. Now, if that were attached to a generator, you would be creating electricity. (Of course, you'd have to blow REALLY hard...)
