Tags Pontiac Sunfire

Subjects

Animals & Plants Arts & Entertainment Auto Beauty & Health Books and Literature Business Electronics Engineering & Technology Food & Drink History Hobbies Jobs & Education Law & Government Math People & Society Science Social Studies Sports Travel & Places

Subjects>Auto>American Cars

Hub torque specifications Pontiac sunfire

Updated: 10/21/2022

Wiki User

∙ 10y ago

Best Answer

185 ft lbs been that way since at the very least 1988.

Wiki User

∙ 10y ago

This answer is:

Add your answer:

Earn +20 pts

Q: Hub torque specifications Pontiac sunfire

Write your answer...

Submit

Still have questions?

What is the torque spec for the front bearing hub on a 2004 Pontiac sunfire?

The 3 bolts on the hub are 65 foot pounds, and the axle nut is 165 foot pounds.

Torque specifications for hub bearing assembly 2004 trailblazer?

103ftlbs

How do you change rear wheelbearings on Pontiac Sunfire?

OK ... Here's the REAL answer: You cannot change the bearings on a Pontiac Sunfire. You must replace the "Hub-Assembly" they will be the same on both sides .

Torque specifications for hub bearing assembly 2004 grand prix?

55 foot pounds

What are the torque specs on a 2003 Malibu hub bearing?

The 2003 Malibu hub bearing torque specifications are 40 pounds per square inch. You can ruin the bearing by tightening it too much.

What size is the socket for a wheel bearing hub for a 2005 Pontiac sunfire?

I'm fairly certain it's a 30mm.

What is torque spec for wheel bearing for a 1998 sunfire?

For the front end of a 2000 sunfire I believe it is 183 foot pounds. Check the sheet that comes with the hub assembly, it should say there.

What front axle bearings does a 2001 Pontiac sunfire use?

Luckily, it isn't pressed in. It's a hub assembly. Just bolts in and out.

To replace a front wheel hubbearing for a 2002 Pontiac sunfire What if the haynes manual that you have for this year of sunfire does not have a section for removal of the hub how do you remove it?

you have to take all brakes and rotor off the hub. then you must spin the hub so the access hole is in front of the bolts,and take all 3 bolts off. then you must pull the hub off of the spline.

Torque specifications for hub bearing assembly 2006 trailblazer?

Hub/bearing assembly to steering knuckle bolts, 77 ft lbs.Axle nut, 103 ft lbs.

Torque specifications on a front wheel bearing assembly for a 2004 Impala LS?

Using new bolts, torque the front hub/bearing assembly to 96 ft-lbs.....

What is the price for a front wheel bearing for a 2000 Pontiac sunfire?

Well its a wheel bearing hub assembly that you need to buy. Autozone has a Timken/Wheel Bearning/Hub Assembly-front its $79.99 and they have the Duralast/Wheel Bearing/Hub Assembly-Front $51.99

Trending Questions

How much does it cost to replace a head-gasket? What sending unit do you need when changing from an idiot light instrument panel to a panel with gauges? Where can you find a copy of a fuse box diagram for a 2001 ford expedition XLT? How do you replace a broken ignition on a 1994 ford ranger? Do you have to drop the back axle to get the gas tank out of an 1988 Chevy Camaro RS? How do you test a ecm on 1990 Chevy 5.7? Will a Monte Carlo door fit an 86 caprice classic? What is the easiest way to replace spark plugs on a 2001 Ford Expedition with coil on plug ignition? Heater blower not working in 1994 geo metro any suggestions? How do you set timing on a 2001 Chevrolet s 10 with a 4.3liter v6? Is carmal a color? How much does it Cost to replace struts 03 cadillac cts? Where do you install the flasher in a 1961 Chevrolet Impala? What happens when you put a matchstick near petrol? Where is the pcv location on a 2.2 s-10? How do you bleed the ABS on a 1998 Dodge Grand Caravan SE? Do 2001 ford transit vans have power steering belts? Where is the starter located in the 1990 dodge spirit? 1995 ford f 150 engine misses all the time? How do you remove the factory radio from a 1998 ford ranger?