0
I figured it out myself. I couldn't see paying the dealer's service area $30.00 to replace a tailight so I bought one at NAPA for $1.49. After opening the hatch, 2 screws are visible on the inner lip of the lens cover. Unscrew these and the casing is slightly loose. I took a wide paint scaper and GENTLY pried the casing away from the body (outwards). There are 2 pins that hold the outer rim of the casing to the metal of the car (opposite of the side containing the screws). Replace the bulb, adjust the wires and then push the casing pins back into the body of the car. Tighten the srews. My greatest fear was to snap a piece of plastic off and not be able to reattach the casing tightly. This did not happen and I am very happy.
What else can I help you with?
Where is the turn signal flasher in a 1999 cirrus?
Its on the top of the steering column underneath the plastic piece.There are 2 screws underneath the column that need to be removed so that the plastic piece can be removed, and then once removed you can see the flasher. its a square black box.just unplug and replace.
How to replace speed sensor on 1999 neon?
The speed sensor is located on the side of the transmission. It has a black plastic teardrop shape to it. It has one bolt that needs to be removed to replace it.
How do you replace the engine air filter in a 2006 sts cadillac?
Open hood. Remove plastic housing securing air filter. Install new filter. Replace what you have removed. Your finished!
How do you replace a bulb located in the rear of a 1993 Lexus ES300?
Along the rear of the inside of the trunk there are four small bolts which need to be removed. Once removed, you will be able to push out the outer plastic cover holdind the light bulbs and wiring. From there, you can easily remove and replace the bulbs.
How do you replace the windshield wiper motor on 1998 olds intrigue?
Should be able to access under hood at center firewall plastic panel may have to be removed
How do you replace the rear speakers in a 1993 Chevy Silverado K1500 Ext Cab?
Remove the plastic head liner panel (roof)Take out the plastic side storage bins in the backseat (sides) Then the rear window plastic side plates can be removed. Factory 4x6's.
How do you access the tail lights and back up lights located on the rear door of a 1990 Lexus ls400 to replace the bulb?
To replace the upper light on the hatchback door, the plastic trim piece just snaps in place, once that is removed the light assembly snaps down to reveal the bulb. The stop lights on the body have the attaching screws covered by plastic plus, just pry them out and remove the screws and the assembly can be removed
How do you replace a keyboard on a laptop?
It really depends on the model probably best to contact the manufacturer, what make is it as some are easily removed from the top by removing a plastic strip like on Toshibas.
How to replace tail lights on a Lexus rx 330?
First remove the felt covered piece on the interior of the tailgate. After that, removed the large plastic piece in order to get inside to the bulb.
Backdoor won't open on 2005 Toyota sequoia?
Removed the back panel from inside staring from top to bottom of the plastic, and you will be able to open. Then replace the back door handle.
How do you replace an air filter in a 1999 dodge grand caravan?
When you open the hood, there is a plastic box to the right side that says "remove to replace air filter". Do not try to pop the top off of this box as i did, instead remove the two screws holding it to the body of the vehicle. The box containing the air filter is located beneath the box you just removed. There are two clips holding the cover on the box, undo these and you will see the filter sitting vertically in the box, replace it, put the cover clips back in place and replace the plastic box that was removed first.
How do you replace the antenna on a 2000 Honda Odyssey?
To replace the antenna on a 2000 Honda Odyssey, first, remove the plastic cover at the base of the antenna by gently prying it off. Next, unscrew the old antenna from the base by turning it counterclockwise. Once removed, screw in the new antenna in a clockwise direction and ensure it’s securely attached. Finally, replace the plastic cover to finish the installation.
