0
What else can I help you with?
Where is the serial number on a Iver Johnson revolver?
under the grip plate
When was Colt revolver?
When was Colt revolver? That's a strange question. You might want to clarify.
How do you dismantle a S and W mod 19.3?
A Smith and Wesson model 19-3 is a .357 magnum revolver, six shot, blued, the 3 means third change. To dismantle the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left. When the grips are removed the side plate will be fully visible. Remove the 3 screws from the side plate. To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit. Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off, so be sure it falls on a padded surface. At this point most internal parts will be visible and accessible. To reassemble the revolver, do the above in reverse, making sure the hammer block is in place and the side plate seats correctly. You can tap on the side plate with a wood or plastic tool to seat it properly. Replace the screws in the correct place along with the grips and grip screw.
How do you reinstall the side plate on a rimfire spur trigger revolver made by crescent pat. apr. 23 1878 30 caliber?
To reinstall the side plate on a Crescent spur trigger revolver, first ensure the revolver is unloaded and safe to handle. Align the side plate with the frame, ensuring that any internal components fit into their respective notches. Gently press the side plate into place, making sure it sits flush against the frame. Finally, secure it with the appropriate screws without overtightening, as this could damage the frame or plate.
How much is it worth Smith weston 37 niquel plate wood grip revolver?
50-325 usd
Colt police positive revolver 1905?
What do you want to know???
When was colt?
When was Colt revolver? That's a strange question. You might want to clarify.
Colt 357 mark III revolver nickel plate worth?
A Colt .357 Mark III nickel plated revolver is worth between $500 and $750. The actual value varies greatly based on the gun's overall condition.
How do you disassemble a smith and Wesson model MP?
A Smith and Wesson M&P model is a 6 shot revolver in 38 Smith & Wesson Special caliber. The MP or M&P stands for "military and police".To disassemble the revolver, first remove the grip screw from the left side of the revolver as the revolver barrel faces to the left.When the grips are removed the side plate will be fully visible.Remove the screws from the side plate.To remove the side plate, hold the revolver to the horizontal position with the side plate facing down. Do not pry off the side plate as that will damage the side plate fit.Sharply rap the now exposed grip frame with a wood or plastic hammer until the side plate loosens. Continue to rap, and the side plate will fall off along with the hammer block, so be sure it falls on a padded surface.At this point most internal parts will be visible and accessible.The cylinder can be removed by sliding the cylinder crane to the left and out of the frame, while holding the cylinder in place.The cylinder will now be free.To reassemble the revolver, do the above in reverse, making sure the hammer block is in place and the side plate seats correctly.You can tap on the side plate with a wood or plastic tool to seat it properly.Replace the cylinder crane and cylinder. Be sure the correct screw is used to hold the cylinder crane to the frame.Replace the remaining side plate screws in the correct place along with the grips and grip screw.Holding back the hammer slightly, or with the hammer cocked, look in the gap between the hammer and frame to be sure the hammer block has been replaced.A word of caution here: know exactly what you are doing before making alterations or repairs. Revolvers are delicate and expensive machinery.
What is a good airsoft revolver?
this depends on a few things: if you want a gas airsoft revolver you can get a crossman or an HFC revolver. If you want a spring revolver the only one is the UHC revolver. the most realistic of the three is the UHC because it only fires six shots before you need to reload (the others fire 10 shots) the UHC is also the cheapest. But the more practical revolvers are the gas ones because you get more shots without having to reload (which is a use full feature when playing in an airsoft war). So take your pick. But if you want the best of the best revolvers in airsoft you should get a WG 700 series revolver or a Dan Wesson revolver. They are co2 revolvers that shoot extremely hard. They are somewhere in the 100-125$ range
What is a good concealed carry revolver that can fire .357 and .38?
Your are asking for an opinion. There are several revolvers that would fill this role well- in my personal opinion, the Smith & Wesson Mdl 60 revolver in .357 Magnum would be the revolver of choice. You may also want to look at the Ruger SP101, preferably, in a hammerless configuration if you want it for concealed carry.
What is the difference between a 38 special revolver and aregular revolver?
38 special is only a revolver caliber. that's like saying a 44 magnum revolver or a 500 special revolver. a revolver is a revolver
