A:
The inductor does not allow ac signal to pass through. It blocks ac and passes dc. If the switch is open, then the ac signal wont pass. If the switch is closed, then the ac signal will pass through the switch.
Answer
It is incorrect to say that an inductor 'does not allow' the passage of an alternating current. An a.c. current will pass through an inductor, although the inductor will limit the value of that current due to the inductor's inductive reactance. Inductive reactance, which is expressed in ohms, is directly-proportional to the inductance of the inductor and to the frequency of the supply. The value of the current is determined by dividing the supply voltage by the inductive reactance of the inductor.
If the switch is connected in parallel with the inductor, then closing the switch will apply a direct short circuit across the inductor, and the resulting short-circuit current will cause the circuit's protective device (fuse or circuit breaker) to operate.
A: Current flow only if there is a return path to the source it does not matter what it is connected to. What leaves at one end of the source will be identical to the return in current
Voltmeter should be connected always in parallel to a circuit ANSWER : IT should be in parallel except when used to measure current. Then it should be placed in series across a shunt.
Eli the ice man. Voltage (E) before Current (I) in a coil (inductor)(L) Current (I) before Voltage (E) in a Cap. (C) Got it?
LC are connected in parallel combination to short out signals too high or too low in frequency from getting to the load.FYI:Series LC circuits give minimum impedance at resonance, while parallel LC (“tank”) circuits give maximum impedance at their resonant frequency.The LC circuit behaves as an electronic resonator, which are the key component in many applications. Oscillators Mixers Graphics tablets Filters Electronic article surveillance & TunersFor example: a capacitor/inductor oscillator acts as the tuner for the radio.The sine wave that matches that particular frequency will get amplified by the resonator, and all of the other frequencies will be ignored. In a radio, either the capacitor or the inductor in the resonator is adjustable. This is how you "tune in" different stations on the radio :)In a nutshell: A series resonant circuit provides voltage magnification and a parallel resonant circuit provides current magnification.
because current in parellel divides unlike in series if one fails all will failsAnswerThe parallel circuit's load current doesn't 'divide'. It's the other way around! Each branch draws an individual current which then 'combine' to form the circuit's load current. However, the reason that the remaining lamps connected in parallel always work, even if one fails, is because each branch of a parallel circuit is subjected to a common supply voltage.
When they are in parallel the same voltage appear across both. The resistor carries a current of V/R, the inductor carries a current of V/(jwL). So the current in the inductor is 90 degrees behind in its phase.
Inside the circuit loop between the inductor and capacitor the current will be at maximum. Outside the circuit the current through the LC tank circuit will be at minimum. It depends on where you are measuring it.
When an inductor is suddenly connected in parallel with a charged capacitor, the current through the inductor and the voltage between its ends will oscillate at the frequency of F = 1 / 2 pi sqrt(L x C) . With real-world components, having resistance and connected through wire that has resistance, the amplitude of the oscillation will steadily decrease as energy is lost in the circuit, and the oscillation will eventually become too small to measure, and disappear.
A resistor or an inductor. The inductor limits transient current, not steady state current.
THE PARALLEL rlc CIRCUIT IS CALLED A REJECTOR CIRCUIT BECAUSE IT REJECTS DOWN THE CURRENT. THE REASON IS AT RESONANCE THE IMPEDENCE OF THE CAPACITOR BECOMES EQUAL TO THAT OF THE INDUCTOR SO NO CURRENT FLOWS. AT LOW FREQUENCY THE CAPACITIVE REACTANCE IS LOW SO ALL THE CURRENT FLOWS THROUGH THE INDUCTOR AND WHEN THE FREQUENCY IS HIGH ALL THE CURRENT WILL FLOW THROUGH THE CAPACITOR BECAUSE AT THAT POINT THE REACTANCE OF THE CAPACITOR IS LOW. SO WE OBTAIN A V-SHAPED GRAPH WITH THE PEAK OF V INDICATING THE REJECTION OF CURRENT.
Parallel Parallel
The difference between a series and parallel circuit is that a series circuit is connected in such a way that the same current intensity flows through the elements while a parallel circuit is connected in such a way that the same potential appears across their terminals.
Series circuit: elements are connected one after the other; the current (the electrons, or other charge carriers) has to pass through each of the elements in turn. Parallel circuit: elements are connected in such a way that part of the current will pass through one circuit element, part through the other.
Actually Inductor oppose the change of current in the circuit..... Acts like a short circuit in steady state condition....
we use the inductor because it helps the circuit to have an appropriate amount of current, so that the circuit in the appliance will say longer.
A driven RL circuit is a circuit that contains a resistor (R) and an inductor (L) connected in series with an external source of alternating current (AC) or voltage. The external source provides energy to the circuit, driving the current through the inductor and resistor. This circuit can exhibit interesting behavior such as resonance and phase shifts due to the interplay between the inductive and resistive components.
A: Current flow only if there is a return path to the source it does not matter what it is connected to. What leaves at one end of the source will be identical to the return in current