0
What else can I help you with?
New shop 20 amp circuit 32 amp fixture how many fixtures can be put on circuit?
A 32 amp fixture can not be fed from a 20 amp breaker as the breaker will trip every time.
What is one and half breaker system in electrical lines?
One and half breaker system is an improvement on the double breaker system to effect saving in the number of circuit breakers. For every 2 circuits, 1 spare breaker is provided: Two feeders are fed from two buses via their associated circuit breakers and these two feeders are coupled by a third circuit breaker which is called tie breaker. During failure of any of the two feeder breakers, the power is fed via the breaker of the second feeder and main breaker (tie breaker).
Can you install a tandem breaker?
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
What type of circuit is most common in household wiring?
The most common types of circuit breaker used are MCBs. (Miniature Circuit Breakers.)The most common type of breaker used in most every residence in the U.S.A. is the non-adjustable trip breaker.
Every time you vacuum you blow the breaker in your house can you change the breaker?
Either your breaker switch needs to be changed for a heavier one, the pool equipment needs to be put on an other circuit or better still one of its own.It is best to talk to an ellectrician about the delails involved.
How many 20 amp branch circuits are required for appliances the minimum?
The number of 20 amp branch circuits required for appliances depends on the total electrical load of the appliances. A general rule is to have one 20 amp circuit for every 600-700 square feet of living space. It is best to consult with an electrician to determine the specific requirements for your appliances.
Give one advantage of using a circuit breaker rather than a wire or cartridge fuse?
An electrical breaker is dual function an electrical fuse just has one purpose.
What is a Circuit Breaker Panel?
A circuit breaker is a overcurrent device. It prevents fire.An electrical circuit is only as strong as its weakest link. When the voltage rating of a device is exceeded, it arcs. Current overloads are less obvious and easier to create. When the current rating of a device is overloaded, the device gets hot, eventually burning up. This can cause a fire.You want your breaker to be your weakest link, because it is designed to safely handle overcurrent situations. If your breaker is not the weakest link, wiring or a wiring device in your home will fail first, possibly setting your home on fire.Some things to remember:A breaker is a safety device. It is there to protect conductors and equipment.Only a Ground Fault Circuit Interrupter (GFCI) breaker will protect people from a shock or electrocution.If it pops, something is wrong. Chances are it is not the breaker! It is against the NEC to reset a breaker unless you know it was an overload condition. If it is a short-circuit, it must be fixed before resetting.Do not replace a breaker with a larger one. The circuit it is feeding cannot handle the extra current and will burn up before the new breaker trips.If a breaker trips frequently, chances are it is overloaded. Look into splitting the circuit it powers into multiple circuits on multiple breakers.If in doubt, call an electrician. Negligence is fatal with electricity.
Why won't the switch on my breaker box stay on?
This is properly understood when Ohm's Law is applied: Voltage, Amperege and Resistance are correctly applied to a circuit for it's correct function. The circuit breaker acts as a protective device and trips when a correct electrical circuit does not exist. The wrong breaker may have been installed. the wrong gauge of wire may have been used, the pumps and heaters may be drawing more amps then planned for or a short circuit or loose connection are all possible faults. Contact the electrician that installed the system for resolution of the problem or an outside electrician if the problem isn't corrected. Caution: Water and Electricity should not be trusted when in close proximity.
Do all branches in a parallel circuit have to be on?
No, they do not. Think of it this way. Your house is one huge parallel circuit. Not every branch is on all the time. You turn switches on and off to turn individual branches on and off at will.
Do both the breakers and the outlets need to be GFI if you are running two 15 amp GFI circuits?
If you're using a GFCI breaker then the entire circuit will be protected by just the breaker alone. Every receptacle, switch, etc on that breaker will utilise the GFCI protection. You may have problems with it tripping if you plug in a motor (vacuum, etc) on the circuit.
How much voltage does each branch of a parallel circuit?
Yes. The voltage across every branch of a parallel circuit is the same. (It may not be the supply voltage, if there's another component between the power supply and either or both ends of the parallel circuit.)
