0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What are some of the materials that would be needed to create a vapor barrier in a crawl space?
There are several items needed to create a vapor barrier in a crawl space. Plastic, caulking, wire brushes, and a putty knife is just a few tools and materials needed.
What do you need to determine crawl space?
Crawl space is determined by the space in which your vent system runs. It is usually big enough to crawl through if you really need to. Crawl space also makes it relatively easy to repair a vent system.
How do you get rid of water in your crawl space?
The most frequent cause of crawl space odor is moisture, and a common culprit is improperly designed and installed vents, which can allow rainwater to find its way into the space. Replace or repair leaking vents.
How do you get rid of mold in a crawl space?
Control the water and you control the mold.
What is a thermal barrier?
A thermal barrier is any protective covering or barrier which inhibits the transfer of heat. For example the space shuttle used a thermal barrier to prevent the astronauts from burning to death when entering the earth atmosphere during re-entry. The thermal barrier reduced the heat caused by the friction of the air passing over the spacecraft to acceptable levels. Without it the shuttle would have burn up and disintegrate. The failure of the thermal barrier was the reason that the Space Shuttle Columbia burned up during re-entry on February 1, 2003.
What is the desired moisture for a crawl space?
The crawl space moisture should be kept below 55% to insure mold, mildew and fungus will not grow. Limiting the moisture will also help with keeping the odor down. I hope this helps, you can find more information at crawlspaceinfo.com
What are some of the materials that would be needed to create a vapor barrier in a crawl space?
There are several items needed to create a vapor barrier in a crawl space. Plastic, caulking, wire brushes, and a putty knife is just a few tools and materials needed.
When insulating a homes crawlspace does the paper side face the underside of the flooring above or does it face down?
Vapor retarder (commonly known as Vapor Barrier), is commonly used to keep moisture out of a defined area space or material. The 2006 International Building Code defines Vapor Retarder as follows: VAPOR RETARDER. A vapor-resistant material, membrane or covering such as foil, plastic sheeting or insulation facing having a permeance rating of 1 perm (5.7 ´ 10-11 kg/Pa × s × m2) or less, when tested in accordance with the dessicant method using Procedure A of ASTM E 96. Vapor retarders limit the amount of moisture vapor that passes through a material or wall assembly Vapor barrier is commonly used in crawl spaces to keep the ground moisture out of the insulating materials. In cold areas vapor barrier is applied to the WARM SIDE IN WINTER over the insulation to keep moisture from the living space from getting to the insulation and condensing as the air gets colder on the outside of the wall/floor. The building codes actually require this application in most areas. However, in crawl spaces there is usually a larger amount of moisture in the ground and most jurisdictions allow the vapor barrier material to be applied to the bottom of the insulation or crawl space side. Some jurisdictions require both sides. Remember that the newer codes require a vapor barrier on the ground in crawl spaces. IRC N1102.2.8 Crawl space walls. As an alternative to insulating floors over crawl spaces, insulation of crawl space walls when the crawl space is not vented to the outside is permitted. Crawl space wall insulation shall be permanently fastened to the wall and extend downward from the floor to the finished grade level and then vertically and/or horizontally for at least an additional 24 inches (610 mm). Exposed earth in unvented crawl space foundations shall be covered with a continuous vapor retarder. All joints of the vapor retarder shall overlap by 6 inches (152 mm) and be sealed or taped. The edges of the vapor retarder shall extend at least 6 inches (152 mm) up the stem wall and shall be attached to the stem wall. Ask your local building inspection department for advice and clarification on the best application in your area. Hope this helps! Terry NEW ANSWER To answer the question, you want to insulate the foundation of the crawlspace. Where the house meets the foundation is called the sil box. That is where 90% of the outside air is infultrating your crawlspace. Stop the problems where it starts, The foundation.(the exterior walls).
What are the benefits of putting gutters on a house?
Depends on your basement area. They help divert water that could add excess moisture into your basement or crawl space.
What is the costs per foot of crawlspace insulation installation?
Depending on where you live, if you encapsulate your crawl space, you might not need insulation at all. Encapsulation consists in completely isolating the crawl space from outside air and the ground by lining the whole space (not just the floor) with a sturdy high-performance vapor barrier, sealing it air tight and then conditioning it with a dehumidifier or a crawl space conditioning system. This will make the crawlspace part of the internal envelope of the house and will not only offer thermal protection by eliminating drafts and protecting ducts, it will also control moisture and related problems (mold, rot, dust mites). Studies conducted by Advanced Energy and Habitat for Humanity report that encapsulated crawl spaces make homes in average 18% more energy efficient.
When was Crawl Space - album - created?
Crawl Space - album - was created in 1977-01.
What do you need to determine crawl space?
Crawl space is determined by the space in which your vent system runs. It is usually big enough to crawl through if you really need to. Crawl space also makes it relatively easy to repair a vent system.
Where can one crawl with space insulation?
Crawl space insulation is something you put into crawl spaces in your home to keep out the cold. Crawl space insulation can be purchased at home improvement stores like Home Depot and Lowe's.
Covering crawl space with plastic help?
covering crawl space with plastic help cut down on humidity in the house?
Should a crawl space have plactic sheeting on the ground?
Absolutely. Moisture from the ground (or even concrete floor as water seeps through) will rise up and saturate the crawl space area with moisture. Anything organic in the space- including wooden beams and insulation- runs the risk of growing mold and rot, eventually affecting the structural integrity of the home and overall healthiness. Additionally, termites can enter and devour the moist wood, and mold spores will rise into your home. (This is much more common than many people think- warm air exits out of the upper levels and cool air is sucked up through the crawl space). Unsealed crawl spaces will also bring humidity into the house and be a perfect place for rodents to live and die in. Definitely put something down. And if you have a vented crawl space, you should look into sealing those vents if local housing codes allow for it.
How do you install a furnace in a house with a crawl space?
To install a furnace in a house with a crawl space, follow these steps: Assess the Crawl Space: Before installing the furnace, inspect the crawl space for any signs of moisture or damage. Ensure proper ventilation by checking and, if necessary, installing crawl space vents to promote airflow and prevent moisture buildup. Prepare the Area: Clear the crawl space of any debris or obstacles to create a suitable workspace for installation. Ensure there is adequate space for the furnace unit and access for maintenance. Install Ductwork: If the house doesn't already have ductwork in the crawl space, install it to connect the furnace to the rest of the HVAC system. Seal all duct joints properly to prevent air leaks. Position the Furnace: Choose a suitable location for the furnace within the crawl space, considering factors such as accessibility, clearance requirements, and proximity to existing ductwork. Secure the Furnace: Once the furnace is in position, securely mount it according to the manufacturer's instructions. Ensure it is level and stable to prevent any movement or vibration during operation. Connect Utilities: Connect the furnace to the power supply and fuel source, whether it's gas, oil, or electricity. Follow local building codes and safety guidelines when making these connections. Test and Commission: After installation, test the furnace to ensure it functions correctly. Check for any leaks, unusual noises, or malfunctions. Once everything is in working order, commission the furnace for regular use. By following these steps and ensuring proper ventilation with crawl space vents, you can successfully install a furnace in a house with a crawl space while maintaining a safe and efficient HVAC system.
Where does a GFCI go?
GFCI protection is required for most outdoor receptacles, bathroom , garage wall outlets, kitchen, and all receptacles in crawl space.
